Home › Drivetrain · A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

C176147E14

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A27-21 (L4) - D56-81 (E1)
Y - BR
4L position signal
  1. Ignition switch ON
  2. Transfer position switch on 4L
Below 1.5 V
  1. Ignition switch ON
  2. Transfer position switch not on 4L
11 to 14 V
A27-5 (TFN) - D56-81 (E1)
G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Transfer in neutral
Below 1.5 V
  1. Ignition switch ON
  2. Transfer not in neutral
11 to 14 V
D56-120 (NSW) - D56-81 (E1)
L - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
D56-2 (P) - D56-81 (E1)
G-B - BR
P shift position switch signal
  1. Ignition switch ON
  2. Shift lever in P
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P
Below 1 V
D56-26 (R) - D56-81 (E1)
L-R - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
D56-25 (N) - D56-81 (E1)
G-W - BR
N shift position switch signal
  1. Ignition switch ON
  2. Shift lever in N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in N
Below 1 V
D56-27 (D) - D56-81 (E1)
G - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D
Below 1 V
A27-25 (S) - D56-81 (E1)
Y - BR
S shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in S
Below 1 V
A27-38 (SFTU) - D56-81 (E1)
G - BR
Up-shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever in "+" (up-shift)
Below 1 V
A27-27 (SFTD) - D56-81 (E1)
BE - BR
Down-shift position switch signal
  1. Ignition switch ON
  2. Shift lever in S
11 to 14 V
  1. Ignition switch ON
  2. Shift lever in "-" (down-shift)
Below 1 V
D56-7 (S1) - D56-81 (E1)
R - BR
S1 solenoid signal
1st gear
Below 1 V
Not in 1st gear
11 to 14 V
D56-6 (S2) - D56-81 (E1)
W - BR
S2 solenoid signal
1st, 2nd or 6th gear
11 to 14 V
3rd, 4th or 5th gear
Below 1 V
D56-3 (S3) - D56-81 (E1)
G-W - BR
S3 solenoid signal
1st, 2nd or 3rd gear
11 to 14 V
4th, 5th or 6th gear
Below 1 V
D56-5 (S4) - D56-81 (E1)
G-R - BR
S4 solenoid signal
5th or 6th gear
11 to 14 V
1st, 2nd, 3rd or 4th gear
Below 1 V
D56-4 (SR) - D56-81 (E1)
G - BR
SR solenoid signal
1st, 2nd, 3rd or 4th gear
11 to 14 V
5th or 6th gear
Below 1 V
D56-14 (SL1+) - D56-15 (SL1-)
Y - L
SL1 solenoid signal
5th or 6th gear
Pulse generation
D56-12 (SL2+) - D56-13 (SL2-)
G-R - L-W
SL2 solenoid signal
Engine is idling
Pulse generation
D56-9 (SLT+) - D56-8 (SLT-)
B - G-B
SLT solenoid signal
Engine is idling
Pulse generation
D56-10 (SLU+) - D56-11 (SLU-)
L-Y - L-R
SLU solenoid signal
5th gear (lock-up) or 6th gear (lock-up)
Pulse generation
D56-122 (THO1) - D56-98 (E2)
G-Y - BR
No. 1 ATF temperature sensor signal
No. 1 ATF temperature: 115°C (239°F) or more
Below 1.5 V
D56-99 (THO2) - D56-98 (E2)
L - BR
No. 2 ATF temperature sensor signal
No. 2 ATF temperature: 115°C (239°F) or more
Below 1.5 V
D56-101 (SP2+) - D56-100 (SP2-)
Y - B
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(see waveform 1)
D56-124 (NT+) - D56-123 (NT-)
Y - B
Speed sensor NT signal
Engine idling
(shift lever in P or N)
Pulse generation
(see waveform 2)
A27-10 (CANH) - D56-81 (E1)
GR - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 3)
A27-11 (CANL) - D56-81 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 4)
A27-51 (PWR) - D56-81 (E1)
L - BR
Tow/haul pattern select switch signal
  1. Ignition switch ON
  2. Tow/haul pattern select switch pushed
0 to 1.5 V
  1. Ignition switch ON
  2. Tow/haul pattern select switch not pushed
Pulse generation*

HINT:
*: Voltage is input intermittently as this is an intermittent circuit. (Voltage varies between a peak of 7.5 to 14 V and a low of 0 to 1.5 V.)



    C161208E04
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    D56-101 (SP2+) - D56-100 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)



  2. C162170E03
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    D56-124 (NT+) - D56-123 (NT-)
    1 V/DIV., 2 msec./DIV.
    Engine idling (shift lever in P or N)



  4. C161206E03
  5. Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A27-10 (CANH) - D56-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON



  6. C161207E03
  7. Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    A27-11 (CANL) - D56-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON