Home › Drivetrain ยท AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P0712 .

DTC Code
DTC Detection Condition
Trouble Area
P0711
When either condition below is met:
1. Condition (a)*, (b), (c), (d), (e) and (f) are met (2 trip detection logic)
(a)* After the engine is stopped, 5 hours or more elapse before the engine is started
(b) 10 minutes elapse after the engine is started
(c) The vehicle is driven 4.9 km (3.0 miles) or more after the engine is started
(d) IAT is 15°C (59°F) or more
(e) ECT is 15°C (59°F) or more
(f) ATF temperature is less than 20°C (68°F)
2. Both (a) and (b) are detected: (2-trip detection logic)
(a) Engine coolant temperature is less than 35°C (95°F) after the engine is started
(b) ATF temperature is 105°C (221°F) or more when the engine coolant temperature reaches 60°C (140°F) after 10 sec. or more
No. 1 transmission wire (No. 1 ATF temperature sensor)
  1. *: Except Mexico models

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output from the Automatic Transmission Fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the MIL and stores the DTC.
When the ATF temperature is 105°C (221°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0711: ATF temperature sensor/Rationality check
Required sensors/Components
ATF temperature sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0712, P0713, P2742, P2743 (ATF temperature sensor "A" circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit)
P0110, P0111, P0112, P0113 (IAT (Intake air temperature) sensor circuit)

Condition (A) 
Soak time*
5 hours or more
Duration time from engine start
12 seconds or more
Time after engine start
10 minutes
Driving distance after engine start
4.9 km (3.0 miles) or more
IAT (12 seconds after engine start)
15°C (59°F) or more
ECT (12 seconds after engine start)
15°C (59°F) or more
  1. *: Except Mexico models

Condition (B) 
Duration time for ECT to reach 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
105°C (221°F) or more
ECT (12 seconds after engine start)
Less than 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition (A) or (B)

Condition (A) 
ATF temperature
Less than 20°C (68°F)

Condition (B) 
ATF temperature
105°C (221°F) or more

COMPONENT OPERATING RANGE


Condition (A) 
ATF temperature
20°C (68°F) or more

Condition (B) 
ATF temperature
Less than 105°C (221°F)

WIRING DIAGRAM

Refer to DTC P0712 .

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted

    HINT:
    When DTC P0712 is output and the Techstream output is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and the Techstream output is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal THO1 and the body ground.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit
    If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
    It is not necessary to inspect the circuit when P0711 is set.

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0711 is output
    A
    P0711 and other DTCs are output
    B

    HINT:
    If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID (Click here)
OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (Click here)