DTC P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0756 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 6th. |
|
| P0756 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 5th. |
|
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under S2 stuck ON malfunction | 1st | 2nd | 2nd | 4th | 6th | 6th |
| *2: Actual gear position under S2 stuck OFF malfunction | 3rd | 3rd | 3rd | 4th | 5th | 5th |
| Related DTCs | P0756: Shift solenoid valve S2/Functional check |
| Required sensors/Components | Shift solenoid valve S2 |
| Frequency of operation | Continuous |
| Duration | 0.4 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed - Turbine speed (NE - NT) | 50 rpm or more |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Turbine speed/Output speed (NT/NO) | 1.24 or more, and 1.49 or less (This means actual gear is 3rd) |
| Turbine speed/Output speed (NT/NO) | 0.66 or more, and 0.80 or less (This means actual gear is 5th) |
| Turbine speed/Output speed (NT/NO) | 0.51 or more, and 0.65 or less (This means actual gear is 6th) |
| Turbine speed/Output speed (NT/NO) | 0.51 or more, and 0.65 or less (This means actual gear is 6th) |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position by yourself |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S2 | ON | ON | OFF | OFF | OFF | ON |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0756) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0756 is output | A |
| P0756 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S2 |
![]() |
Remove the shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly.
|
| ||||
| OK | ||
| ||