Home › Drivetrain · A760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0766    Shift Solenoid "D" Performance (Shift Solenoid Valve S4)

DTC    P0776    Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body and automatic transmission (clutch, brake, gear, etc.).

DTC Code
DTC Detection Condition
Trouble Area
P0766
  1. S4 stuck OFF malfunction or brake control valve malfunction*:
  2. Shifting to 5th and 6th gears is impossible.
  3. The ECM determines there is a malfunction when the following conditions are both met (2-trip detection logic):
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
  1. Shift solenoid valve S4 remains closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked (brake control valve)
  4. Automatic transmission (clutch, brake, gear, etc.)
P0776
  1. SL2 stuck ON malfunction or brake control valve malfunction*:
  2. Shifting to 5th and 6th gears is impossible.
  3. The ECM determines there is a malfunction when the following conditions are both met (2-trip detection logic):
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
  1. Shift solenoid valve SL2 remains closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked (brake control valve)
  4. Automatic transmission (clutch, brake, gear, etc.)

HINT:
  1. Gear positions in the event of a solenoid valve mechanical problem:

    ECM gear shift command
    1st
    2nd
    3rd
    4th
    5th
    6th
    *: Actual gear position under malfunction
    1st
    2nd
    3rd
    4th
    4th
    4th
  2. Gear position during fail-safe operation:
    If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

    Gear position under normal conditions
    1st
    2nd
    3rd
    4th
    5th
    6th
    *: Actual gear position under fail-safe mode
    1st
    2nd
    3rd
    3rd
    3rd
    3rd


MONITOR DESCRIPTION

This DTC indicates a "stuck OFF malfunction" of the shift solenoid valve S4, a "stuck ON malfunction" of the shift solenoid valve SL2, or a brake control valve malfunction. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not same, the ECM illuminates the MIL and stores the DTCs.

MONITOR STRATEGY


Related DTCs
P0766: Shift solenoid valve S4/Functional check
P0776: Shift solenoid valve SL2/Functional check
Required sensors/Components
Shift solenoid valve S4, Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE)
Frequency of operation
Continuous
Duration
0.4 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor circuit)
P0500 (Output speed sensor circuit)
P0327, P0328, P0332, P0333 (KCS sensor circuit)
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve S3 circuit
Not circuit malfunction
Shift solenoid valve S4 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
ECT (Engine Coolant Temperature) sensor circuit
Not circuit malfunction
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting
Transfer position
HIGH*

HINT:
*: Following conditions are met

Vehicle speed sensor "A" circuit
Not circuit malfunction
Output shaft speed sensor circuit
Not circuit malfunction
Transfer output speed
143 rpm or more
Transfer input speed / Transfer output speed (NO / NOtf)
0.9 or more, and less than 1.1


P0766 OFF Malfunction (A) and P0776 ON Malfunction (A) 
ECM selected gear
5th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.6% or more at 2000 rpm
(Conditions vary with engine speed)

P0766 OFF Malfunction (B) and P0776 ON Malfunction (B) 
ECM selected gear
6th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.6% or more at 2000 rpm
(Conditions vary with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. Both of the following conditions are met: OFF malfunction (A) and (B)

P0766 OFF Malfunction (A) 
Turbine speed / Output speed (NT / NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)

P0766 OFF Malfunction (B) 
Turbine speed / Output speed (NT / NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)
[ON malfunction]
  1. Both of the following conditions are met: ON malfunction (A) and (B)

P0776 ON Malfunction (A) 
Turbine speed / Output speed (NT / NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)

P0776 ON Malfunction (B) 
Turbine speed / Output speed (NT / NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (30 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
    2. The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.
    3. The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.
    6. The shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      6th
      Shift solenoid valve S4
      OFF
      OFF
      OFF
      OFF
      ON
      ON
      Shift solenoid valve SL2
      ON
      ON
      ON
      ON
      OFF
      OFF

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0766 AND P0776)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0766 and P0776 are output
    A
    P0766, P0776 and other DTCs are output
    B

    HINT:
    If any other codes besides P0766 and P0776 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test while the ATF temperature is 50 to 80°C (122 to 176°F).
  2. Be careful to prevent the hose of SST from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C210149E02
  1. Remove the test plug from the center of the right side of the transmission case and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.

    Text in Illustration 
    *1
    Test Plug



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE S4


    C208651E03
  1. Remove shift solenoid valve S4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve S4 connector
    2. Battery negative (-) → Shift solenoid valve S4 body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S4)


NG
REPLACE SHIFT SOLENOID VALVE S4
OK


4.INSPECT SHIFT SOLENOID VALVE SL2


    C197715E08
  1. Remove shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL2)


NG
REPLACE SHIFT SOLENOID VALVE SL2
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)