DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
|
|
| Related DTCs | P0705: Park/neutral position switch/Verify switch input |
| Required sensors/Components | Park/neutral position switch |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B) 2 seconds Condition (C) 60 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | None |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| P switch | ON |
| N switch | ON |
| NSW switch | ON |
| R switch | ON |
| D switch | ON |
| P switch | ON |
| N switch | ON |
| NSW switch | ON |
| R switch | ON |
| P switch | OFF |
| N switch | OFF |
| NSW switch | OFF |
| R switch | OFF |
| D switch | OFF |
| Park/neutral position switch | The park/neutral position switch sends only one signal to the ECM |

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (N Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| 1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the D21 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift lever in P | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever in N | Below 1 Ω |
| 2 (RB) - 7 (DL) |
| Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | 10 kΩ or higher |
| Shift lever not in N | 10 kΩ or higher |
| 2 (RB) - 7 (DL) |
| 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Disconnect the H31 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG) - 7 (S) | Shift lever in S, "+" and "-" | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever not in S, "+" and "-" | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the D21 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D21-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| D21-2 (RB) - Body ground | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE) |
![]() |
Disconnect the H31 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H31-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H31-3 (IG) - Body ground | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the D56 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|
| 11 to 14 V |
| D56-26 (R) - Body ground |
| 11 to 14 V* |
|
| 11 to 14 V |
| D56-27 (D) - Body ground |
| 11 to 14 V |
|
| Below 1 V |
| D56-26 (R) - Body ground |
| Below 1 V |
|
| Below 1 V |
| D56-27 (D) - Body ground |
| Below 1 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
![]() |
Disconnect the A27 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A27-25 (S) - Body ground | Shift lever in S, "+" and "-" | 11 to 14 V |
| A27-25 (S) - Body ground | Shift lever not in S, "+" and "-" | Below 1 V |
| Result | Proceed to |
| NG | A |
| OK (for 3UR-FE) | B |
| OK (for 3UR-FBE) | C |
|
| ||||
|
| ||||
| A | ||
| ||