DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 P0345 | No VVT sensor signal to ECM during engine running (1 trip detection logic) |
|
| P0342 P0347 | Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic) |
|
| P0343 P0348 | Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-92 (VV1+) - D56-91 (VV1-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-87 (VV2+) - D56-88 (VV2-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0340: VVT position sensor (for Bank 1) verify pulse input P0342: VVT position sensor (for Bank 1) range check (low voltage) P0343: VVT position sensor (for Bank 1) range check (high voltage) P0345: VVT position sensor (for Bank 2) verify pulse input P0347: VVT position sensor (for Bank 2) range check (low voltage) P0348: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | None |
| VVT sensor voltage | 0.3 to 4.7 V |
| Engine speed | 600 rpm or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Ignition switch | ON |
| Camshaft position sensor range check failure (P0342, P0343, P0347, P0348) | Not detected |
| Monitor runs whenever following DTCs are not stored | None |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery Voltage | 8 V or more |
| Camshaft position sensor verify pulse input failure (P0340, P0345) | Not detected |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the D22 or D23 VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM) |
![]() |
Disconnect the D22 or D23 VVT sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D22-1 (VVL+) - D56-92 (VV1+) | Always | Below 1 Ω |
| D22-2 (VVL-) - D56-91 (VV1-) | Always | Below 1 Ω |
| D23-1 (VVR+) - D56-87 (VV2+) | Always | Below 1 Ω |
| D23-2 (VVR-) - D56-88 (VV2-) | Always | Below 1 Ω |
| D22-1 (VVL+) or D56-92 (VV1+) - Body ground | Always | 10 kΩ or higher |
| D22-2 (VVL-) or D56-91 (VV1-) - Body ground | Always | 10 kΩ or higher |
| D23-1 (VVR+) or D56-87 (VV2+) - Body ground | Always | 10 kΩ or higher |
| D23-2 (VVR-) or D56-88 (VV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.CHECK INTAKE CAMSHAFT (TEETH) |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR (FOR INTAKE SIDE) |
Replace the VVT sensor (for Intake side) (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 | B |
|
| ||||
| A | ||
| ||