Home › Engine / Hybrid System ยท 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC Code
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leakage from exhaust system
  7. Open or short in A/F sensor (for Sensor 1) circuit
  8. A/F sensor (for Sensor 1)
  9. A/F sensor heater (for Sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
  15. Fuel pressure switching valve
  16. Fuel pressure regulator
  17. Fuel pressure regulator for high pressure
  18. Fuel pump
  19. Fuel pump ECU
  20. Fuel sender gauge assembly
  21. Wire harness or connector
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
  1. Injector leakage or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leakage from exhaust system
  7. Open or short in A/F sensor (for Sensor 1) circuit
  8. A/F sensor (for Sensor 1)
  9. A/F sensor heater (for Sensor 1)
  10. Integration relay
  11. A/F sensor heater and integration relay circuits
  12. ECM
  13. Fuel pressure switching valve
  14. Fuel pressure regulator
  15. Fuel pressure regulator for high pressure
  16. Fuel pump
  17. Fuel pump ECU
  18. Fuel sender gauge assembly
  19. Wire harness or connector

HINT:
  1. When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is +35% or more or -35% or less, the ECM interprets this as a fuel system malfunction.

A121607E01


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim lean (for Bank 1)
P0172: Fuel trim rich (for Bank 1)
P0174: Fuel trim lean (for Bank 2)
P0175: Fuel trim rich (for Bank 2)
Required Sensors/Components (Main)
Fuel system
Required Sensors/Components (Related)
A/F sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil control valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P2440 - P2447 (Secondary air injection system)
P0500 (Vehicle speed sensor)
Fuel system status
Closed loop
Battery voltage
11 V or more
Either of following conditions 1 or 2 met
-
1. Engine speed
Below 1100 rpm
2. Intake air amount per revolution
0.36 g/rev or more
Catalyst monitor
Not executed
Ethanol content learning
Not executed
Refuel with small amount or on an incline
Not executed

TYPICAL MALFUNCTION THRESHOLDS


Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average of short-term fuel trim and long-term fuel trim
35% or more (varies with ECT)
2. Average of short-term fuel trim and long-term fuel trim
-35% or less (varies with ECT)

CONFIRMATION DRIVING PATTERN


A199233E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or more with all the accessories switched OFF [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at a speed between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1,400 rpm and 3,200 rpm for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0171, P0172, P0174 or P0175.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (ALCOHOL DENSITY ESTIMATE, SHORT FT, LONG FT) [STEP *1]
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Make sure that the Data List item "Alcohol Density Learning" is "Compl".

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT and Long FT.

  1. Check the data list values, and then write them down.


NEXT


3.CONFIRM ALCOHOL CONCENTRATION IN FUEL [STEP *2]
  1. Confirm the alcohol concentration in the fuel .

  1. Write down the alcohol concentration in the fuel.


NEXT


4.CONFIRM LEARNED VALUE
  1. Use the following formula to calculate the difference between the learned values from step *1 and the actual alcohol concentration in the fuel from step *2.

    HINT:
    | ((Alcohol Density Estimate / 2) + Short FT + Long FT) - (Alcohol Concentration in Fuel / 2) | < 35%


    Result 
    Result
    Proceed to
    Difference is 35% or more
    A
    Difference is less than 35%
    B



B
Go to step 6
A


5.CHECK FUEL INJECTION SYSTEM
  1. Check the fuel injection system (Click here).

    HINT:
    If the problem area cannot be determined by checking the fuel injection system, proceed to the next step.



NEXT
Go to step 9

6.CONFIRM LEARNED VALUE
  1. Use the following formula to calculate the difference between the learned value from step *1 and the actual alcohol concentration in the fuel from step *2.

    HINT:
    | (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) | < 10%


    Result 
    Result
    Proceed to
    Difference is 10% or more
    A
    Difference is less than 10%
    B



B
Go to step 9
A


7.CONFIRM ALCOHOL CONCENTRATION IN FUEL
  1. Confirm the actual alcohol concentration in the fuel from step *2.

    Result 
    Result
    Proceed to
    Alcohol concentration is 20% or less
    A
    Alcohol concentration is more than 20%
    B



A
Go to step 10

B
Go to step 8

8.REPLACE FUEL
  1. Replace the fuel with E0 gasoline (replace approximately 20 liters (5 gallons) of fuel).

  1. Disconnect the cable from the negative (-) battery terminal for more than 1 minute.



NEXT
Go to step 10

9.ADD FUEL
  1. Disconnect the cable from the negative (-) battery terminal for more than 1 minute.

  1. Add at least 8 liters (2 gallons) of fuel.

    HINT:
    Check "Fuel Remaining Volume" in the Data List and if it has a value of 85% or more, remove enough fuel so that the value decreases to less than 85% before adding fuel.

  1. Make sure that the Data List item "Alcohol Density Learning" is "Incmpl".



NEXT
Go to step 11

10.PERFORM INITIALIZATION (FUEL DENSITY LEARNING VALUE RESET)
  1. Perform initialization (Fuel Density Learning Value Reset).

    HINT:
    1. After clearing the learned value, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.
    2. If "Fuel Density Learning Value Reset" is performed after warming the engine coolant up to approximately 50°C (122°F), the engine becomes easier to start afterward.


NEXT


11.CONFIRM LEARNED VALUE

HINT:
If the difference between the learned value of the vehicle from step *1 and the actual alcohol concentration in the fuel from step *2 is less than 10%, it is not necessary to perform learning.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Make sure that the Data List item "Alcohol Density Learning" is "Compl".

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT and Long FT.

  1. Check the data list values, and then write them down.

  1. Confirm the alcohol concentration in the fuel .

  1. Write down the alcohol concentration in the fuel.

  1. Use the following formula to calculate the difference between the current learned value and the actual alcohol concentration in the fuel.

    HINT:
    | (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) | < 10%


    OK:

    Result
    Specified Condition
    Difference between actual alcohol concentration and Alcohol Density Estimate
    Less than 10%
    Short FT and Long FT
    Between -35% and 35%



NG
Go to step 2
OK

END