DTC P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) |
DTC P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0013 | Open or short in OCV for exhaust camshaft (for Bank 1) circuit (1 trip detection logic) |
|
| P0023 | Open or short in OCV for exhaust camshaft (for Bank 2) circuit (1 trip detection logic) |
|
| Related DTCs | P0013: Exhaust camshaft OCV (for Bank 1) P0023: Exhaust camshaft OCV (for Bank 2) |
| Required sensors/Components (Main) | Exhaust camshaft OCV |
| Required sensors/Components (Related) | - |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not stored | None |
| All of following conditions met | - |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 0.5 seconds or more |
| One of following conditions met | - |
| A. All of following conditions met | - |
| Battery voltage | 11 to 13 V |
| Target duty ratio | Less than 70% |
| Output signal duty ratio | 100% |
| B. All of following conditions met | - |
| Battery voltage | 13 V or more |
| Target duty ratio | Less than 80% |
| Output signal duty ratio | 100% |
| C. Both of following conditions met | - |
| Current cut status | Not cut |
| Output signal duty ratio | 3% or less |
| OCV duty-cycle | 3 to 100% when engine running |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK DTC (DTC P0013 OR P0023) |
Connect the Techstream to the DLC3.
Clear DTC after recording the freeze frame data and DTC.
Turn the ignition switch off.
Allow the engine to idle and check DTC.
Check that P0013 or P0023 is not output.
|
| ||||
| OK | ||
| ||
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft timing oil control valve assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (OCV - ECM) |
![]() |
Disconnect the D28 or D29 OCV connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D28-1 - D56-56 (OE1+) | Always | Below 1 Ω |
| D28-2 - D56-55 (OE1-) | Always | Below 1 Ω |
| D29-1 - D56-50 (OE2+) | Always | Below 1 Ω |
| D29-2 - D56-49 (OE2-) | Always | Below 1 Ω |
| D28-1 or D56-56 (OE1+) - Body ground | Always | 10 kΩ or higher |
| D28-2 or D56-55 (OE1-) - Body ground | Always | 10 kΩ or higher |
| D29-1 or D56-50 (OE2+) - Body ground | Always | 10 kΩ or higher |
| D29-2 or D56-49 (OE2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||