Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0014    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0015    Camshaft Position "B" - Timing Over-Retarded (Bank 1)

DTC    P0024    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0025    Camshaft Position "B" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

HINT:
If DTC P0014, P0015, P0024 or P0025 is present, check the VVT (Variable Valve Timing) system.

The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

A192077E02


DTC Code
DTC Detection Condition
Trouble Area
P0014
P0024
Exhaust valve timing is not adjusted in valve timing advance range
(2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Valve timing
  3. Oil control valve (OCV) for exhaust camshaft
  4. OCV filter
  5. Camshaft timing exhaust gear
  6. ECM
P0015
P0025
Exhaust valve timing is not adjusted in valve timing retard range
(1 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Valve timing
  3. OCV for exhaust camshaft
  4. OCV filter
  5. Camshaft timing exhaust gear
  6. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and sets a DTC.
  1. Example:
  2. A DTC is set when the following conditions "A" and "B" are met:
    1. (a)It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").
    2. (b)After the above condition is met, the camshaft timing oil control valve assembly is forcibly activated for 10 seconds (Condition "B").
  3. DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.

MONITOR STRATEGY


Related DTCs
P0014: Advanced camshaft timing (for Bank 1)
P0015: Retarded camshaft timing (for Bank 1)
P0024: Advanced camshaft timing (for Bank 2)
P0025: Retarded camshaft timing (for Bank 2)
Required Sensors/Components (Main)
VVT OCV and VVT Actuator
Required Sensors/Components (Related)
Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor
Frequency of operation
Continuous
Duration
Within 10 seconds
MIL operation
Advanced camshaft timing: 2 driving cycles
Retarded camshaft timing: Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0013, P0023 (Exhaust VVT Oil control valve)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
Battery voltage
11 V or more
Engine RPM
500 to 4000 rpm
Engine coolant temperature
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced camshaft timing: 
Both conditions are met:
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle)
Valve timing
No change at advanced valve timing

Retarded camshaft timing: 
Both conditions are met:
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle)
Valve timing
No change at retarded valve timing

CONFIRMATION DRIVING PATTERN


A232050E12

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more [C].

    NOTICE:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0014, P0015, P0024 or P0025.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (38 mph) and then decelerating the vehicle 10 to 15 times [F].

    NOTICE:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 30 seconds or more [G].
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  17. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  19. Perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0013 .

INSPECTION PROCEDURE


HINT:

Abnormal bank
Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1
P0014
P0015
Bank 2
P0024
P0025
  1. If DTC P0014 or P0015 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. If DTC P0024 or P0025 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Display (DTC output)
    Proceed to
    P0014, P0015, P0024 or P0025
    A
    P0014, P0015, P0024 or P0025 and other DTCs
    B

    HINT:
    If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Turn the A/C on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:
    Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    Refer to "Data List / Active Test" [VVT Ex OCV Duty #1, VVT Ex Chg Angle #1, VVT Ex OCV Duty #2 and VVT Ex Chg Angle #2] (Click here).



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. With the engine warmed up, idle it for 1 minute. Then drive the vehicle for 5 minutes.

  1. Read DTCs using the Techstream.

    OK:
    No DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

A166451E01

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING EXHAUST GEAR
  1. Replace the camshaft timing exhaust gear (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. With the engine warmed up, idle it for 1 minute. Then drive the vehicle for 5 minutes.

  1. Read the output DTCs using the Techstream.

    OK:
    No DTC output.

    HINT:
    DTC P0014, P0015, P0024 or P0025 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM IS OK