POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch |

| 1.CHECK LIN COMMUNICATION SYSTEM |
Check for LIN communication system DTCs related to the power window control system (Click here).
|
| ||||
| OK | |
| 2.CHECK DTC (B2312) |
Check if DTC B2312 is output (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING TECHSTREAM (D-DOOR MOTOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / D-Door Motor / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Up SW | Driver side power window MANUAL UP switch signal / ON or OFF | ON: Driver side power window manual UP switch operated OFF: Driver side power window switch not operated | - |
| D Door P/W Down SW | Driver side power window MANUAL DOWN switch signal / ON or OFF | ON: Driver side power window manual DOWN switch operated OFF: OFF: Driver side power window switch not operated | - |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BATTERY, BODY GROUND) |
![]() |
Disconnect the M2 power window regulator master switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M2-3 (B) - Body ground | Always | 11 to 14 V |
| M2-13 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| M2-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the power window regulator master switch assembly connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR LH - BATTERY, BODY GROUND) |
![]() |
Disconnect the M3 front power window regulator motor assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M3-2(B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| M3-1(GND) - Body ground | Always | Below 1 Ω |
Reconnect the front power window regulator motor assembly LH connector.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - FRONT POWER WINDOW MOTOR LH) |
![]() |
Disconnect the M2 power window regulator master switch assembly connector.
Disconnect the M3 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M2-4 (UP) - M3-10 (UP) | Always | Below 1 Ω |
| M2-5 (DOWN) - M3-7 (DOWN) | Always | Below 1 Ω |
| M2-4 (UP) - Body ground | Always | 10 kΩ or higher |
| M2-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
Reconnect the front power window regulator motor assembly LH connector.
Reconnect the power window regulator master switch assembly connector.
|
| ||||
| OK | |
| 7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Remove the front power window regulator motor assembly LH (Click here).
Apply positive (+) battery voltage to the connector terminal 2(B).
Apply negative (-) battery voltage to the connector terminals 1(GND) and 7 (DOWN) / 10(UP).
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (B) Battery negative (-) → (-): 1(GND) (3 sec. or more) → 1(GND) and 10(UP) (within 1 sec.) → 1(GND) (within 1 sec.) → 1(GND) and 10(UP) | Motor gear rotates clockwise |
| Battery positive (+) → 2 (B) Battery negative (-): 1(GND) (3 sec. or more) → 1(GND) and 7(DOWN) (within 1 sec.) → 1(GND) (within 1 sec.) → 1(GND) and 7(DOWN) | Motor gear rotates counterclockwise |
Reinstall the front power window regulator motor assembly LH.
|
| ||||
| OK | ||
| ||