Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

  1. If the manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator switch, the front power window regulator motor RH, the harness and connector.

WIRING DIAGRAM


B184409E06


INSPECTION PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC (B2312) (Click here)
OK


3.READ VALUE USING TECHSTREAM (P-DOOR MOTOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / P-Door Motor / Data List.

  1. According to the display on the Techstream, read the Data List.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Up SW
    Front passenger side power window manual UP switch signal / ON or OFF
    ON: Front passenger side power window manual UP switch operated
    OFF: Front passenger side power window switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual DOWN switch signal / ON or OFF
    ON: Front passenger side power window manual DOWN switch operated
    OFF: Front passenger side power window switch not operated
    -

    OK:
    The Techstream display changes normally when front passenger side power window switch is operated.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)


    B184452E06
  1. Disconnect the L2 Front power window regulator switch assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the Front power window regulator switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (FRONT P/W REGULATOR MOTOR RH - BATTERY, BODY GROUND)


    B180291E09
  1. Disconnect the L3 front power window regulator motor assembly RH connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L3-2 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L3-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the front power window regulator motor assembly RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW SWITCH RH - FRONT POWER WINDOW MOTOR RH)


    B184455E11
  1. Disconnect the L2 front power window regulator switch assembly RH connector.

  1. Disconnect the L3 front power window regulator motor assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-6 (UP) - L3-10 (UP)
    Always
    Below 1 Ω
    L2-7 (DOWN) - L3-7 (DOWN)
    Always
    Below 1 Ω
    L2-8 (AUTO) - L3-4 (AUTO)
    Always
    Below 1 Ω
    L2-6 (UP) - Body ground
    Always
    10 kΩ or higher
    L2-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    L2-8 (AUTO) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the front power window regulator motor assembly RH connector.

  1. Reconnect the front power window regulator switch assembly RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    B184772E08
  1. Remove the front power window regulator switch assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual UP operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual DOWN operation
    Below 1 Ω

  1. Reinstall the front power window regulator switch assembly RH.



NG
REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)