Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > INITIALIZATION

for Preparation Click here



DESCRIPTION OF INITIALIZATION
  1. Perform initialization in the following cases:

    1. Before delivery of a new vehicle.
    2. After rotating the tires on vehicles whose front and rear tire inflation pressure standard values are different.
    3. After replacement of the tire pressure warning ECU*.
    4. After replacement of the tire pressure warning valve and transmitter*.

    HINT:
    *: Perform initialization after the transmitter ID registration is completed (Click here).

  2. Before initialization

    1. Set the air pressure of all tires to the specified value (Click here).

      NOTICE:
      Make sure that the tires are cooled down.


INITIALIZATION PROCEDURE
  1. Turn the ignition switch to ON.



  2. Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.


    C180353E01

  3. Turn the ignition switch off.

  4. Connect the Techstream to the DLC3.

  5. Turn the ignition switch to ON and turn the Techstream on.

  6. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.



  7. H102392E79
  8. Confirm that the tire pressure data of all tires are displayed on the Techstream screen in order to check the completion.

    NOTICE:
    1. The initialization is normally completed within 5 to 6 minutes.
    2. If the initialization has not been completed successfully, DTC C2177/77 is set after the vehicle is driven for 20 minutes or more.
    3. The initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.


    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*.
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*.
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*.
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*.

    HINT:
    1. The initialization is complete when the Data List "ID Tire Inflation Pressure" display shows the correct pressures.
    2. *: It may take up to about 5 to 6 minutes to update the tire pressure data. If the values are not displayed after about 5 to 6 minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (Click here).