Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running
(2 trip detection logic)
  1. Open in Air Fuel Ratio (A/F) sensor (for Bank 1, 2 Sensor 1) circuit
  2. Air Fuel Ratio (A/F) sensor (for Bank 1, 2 Sensor 1)
  3. ECM
P2238
P2241
  1. Case 1:
Condition (a) or (b) continues for 5.0 seconds or more
(2 trip detection logic):
(a) AF+ voltage 0.5 V or less
(b) (AF+) - (AF-) = 0.1 V or less
  1. Case 2:
A/F sensor admittance: Less than 0.022 1/Ω
(2 trip detection logic)
  1. Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit
  2. A/F sensor (for Bank 1, 2 Sensor 1)
  3. ECM
P2239
P2242
AF+ voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit
  2. A/F sensor (for Bank 1, 2 Sensor 1)
  3. ECM
P2252
P2255
AF- voltage 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit
  2. A/F sensor (for Bank 1, 2 Sensor 1)
  3. ECM
P2253
P2256
AF- voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit
  2. A/F sensor (for Bank 1, 2 Sensor 1)
  3. ECM

HINT:
  1. DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Sensor 1 refers to the sensor closest to the engine assembly.
  6. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops.
To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to the ON position, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.
The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the A/F sensor circuit.

MONITOR STRATEGY


Related DTCs
P2237: A/F sensor (for Bank 1) open circuit between AF+ and AF-
P2238: A/F sensor (for Bank 1) short circuit between AF+ and AF-
P2238: A/F sensor (for Bank 1) short circuit between AF+ and GND
P2238: A/F sensor (for Bank 1) low impedance
P2239: A/F sensor (for Bank 1) short circuit between AF+ and +B
P2240: A/F sensor (for Bank 2) open circuit between AF+ and AF-
P2241: A/F sensor (for Bank 2) short circuit between AF+ and AF-
P2241: A/F sensor (for Bank 2) short circuit between AF+ and GND
P2241: A/F sensor (for Bank 2) low impedance
P2242: A/F sensor (for Bank 2) short circuit between AF+ and +B
P2252: A/F sensor (for Bank 1) short circuit between AF- and GND
P2253: A/F sensor (for Bank 1) short circuit between AF- and +B
P2255: A/F sensor (for Bank 2) short circuit between AF- and GND
P2256: A/F sensor (for Bank 2) short circuit between AF- and +B
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds: A/F sensor open circuit between AF+ and AF- and Low impedance
5 seconds: Other
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


A/F Sensor - Open Circuit Between AF+ and AF- 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC Valve)
Battery voltage
11 V or more
Engine
Running
Estimated sensor temperature
450 to 550°C (842 to 1022°F) for P2237 and P2240

A/F Sensor - Low Impedance 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC Valve)
Engine coolant temperature
0°C (0°F) or higher
Estimated sensor temperature
700 to 800°C (1292 to 1472°F) for P2238 and P2241
Fuel cut
Not executed

A/F Sensor - Short Circuit Between AF+ and AF-, GND 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC Valve)
Battery voltage
11 V or higher
Ignition switch
ON
Timing after ignition switch off to ON
5 seconds or more

Other 
Battery voltage
11 V or higher
Ignition switch
ON
Timing after ignition switch off to ON
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240: 
A/F sensor admittance
Below 0.002 1/Ω

P2238 and P2241: 
When one of following conditions is met:
Condition 1, 2 or 3
1. Sensor admittance
Less than 0.0074 1/Ω
2. AF+ voltage
0.5 V or less
3. Difference of AF+ and AF- voltage
0.1 V or less

P2239 and P2242: 
AF+ voltage
More than 4.5 V

P2252 and P2255: 
AF- voltage
0.5 V or less

P2253 and P2256: 
AF- voltage
More than 4.5 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and wait 5 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E11
  1. Disconnect the D19 or D20 A/F sensor connector.

  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D19-3 (A1A+) - D56-126 (A1A+)
    Always
    Below 1 Ω
    D19-4 (A1A-) - D56-125 (A1A-)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D20-3 (A2A+) - D56-103 (A2A+)
    Always
    Below 1 Ω
    D20-4 (A2A-) - D56-102 (A2A-)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D19-3 (A1A+) or D56-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D19-4 (A1A-) or D56-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    D20-3 (A2A+) or D56-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    D20-4 (A2A-) or D56-102 (A2A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output
    B



B
REPLACE ECM (Click here)
A

END