Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON and check the freeze frame data by following the prompts on the Techstream screen.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tilt Position
    Current tilt position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
    7000 to 9000 H
    (28672 to 36864 edges)
    -
    Telesco Position
    Current telescopic position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
    7000 to 9000 H
    (28672 to 36864 edges)
    -
    Tilt Return Position
    Memorized tilt return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
    7000 to 9000 H
    (28672 to 36864 edges)
    -
    Telesco Return Position
    Memorized telescopic return position data / min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
    7000 to 9000 H
    (28672 to 36864 edges)
    -
    Tilt Up Switch
    Input state of tilt up by manual switch / ON or OFF
    ON: Tilt up is activated by manual switch
    OFF: Tilt up is not activated by manual switch
    -
    Tilt Up SW(CAN)
    Communication state of tilt up input by manual switch / ON or OFF
    ON: Tilt up is activated by manual switch
    OFF: Tilt up is not activated by manual switch
    -
    Tilt Down Switch
    Input state of tilt down by manual switch / ON or OFF
    ON: Tilt down is activated by manual switch
    OFF: Tilt down is not activated by manual switch
    -
    Tilt Down SW(CAN)
    Communication state of tilt down input by manual switch / ON or OFF
    ON: Tilt down is activated by manual switch
    OFF: Tilt down is not activated by manual switch
    -
    Telesco Short Switch
    Input state of telescopic short by manual switch / ON or OFF
    ON: Telescopic short is activated by manual switch
    OFF: Telescopic short is not activated by manual switch
    -
    Telesco Short SW(CAN)
    Communication state of telescopic short input by manual switch / ON or OFF
    ON: Telescopic short is activated by manual switch
    OFF: Telescopic short is not activated by manual switch
    -
    Telesco Long Switch
    Input state of telescopic long by manual switch / ON or OFF
    ON: Telescopic long is activated by manual switch
    OFF: Telescopic long is not activated by manual switch
    -
    Telesco Long SW(CAN)
    Communication state of telescopic long input by manual switch / ON or OFF
    ON: Telescopic long is activated by manual switch
    OFF: Telescopic long is not activated by manual switch
    -
    T&T Manual SW Data
    Voltage data of manual switch / min.: 0.00 V, max.: 4.99 V
    Neutral position: Below 0.2 V
    Tilt up: 1.67 to 2.13 V
    Tilt down: 0.54 to 0.74 V
    Telescopic contract: 1.08 to 1.40 V
    Telescopic extend: 2.22 to 2.77 V
    -
    Power Source Voltage
    Voltage data of power supply / min.: 0.00 V, max.: 19.99 V
    Actual power supply voltage
    11 to 14 V
    -
    Freeze Speed Info
    Vehicle speed data / min: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    IG Switch (CAN)
    Communication state of ignition switch / ON or OFF
    ON: Communication is normal
    OFF: Communication is interrupted
    -
    IG Switch
    Input state of ignition switch / ON or OFF
    ON: Input signal is normal
    OFF: Input signal is interrupted
    -
    Key Switch(CAN)
    Communication state of unlock warning switch signal / ON or OFF
    ON: Communication is normal
    OFF: Communication is interrupted
    -
    Key Switch
    Input state of unlock warning switch / ON or OFF
    ON: Communication is normal
    OFF: Communication is interrupted
    -
    Key Code Confirm(CAN)
    Communication state of key code confirmation signal / ON or OFF
    ON: Communication is normal
    OFF: Communication is interrupted
    -
    Receive from Meter
    Communication state of combination meter signal / OK or Interpt
    OK: Communication is normal
    Interpt: Communication is interrupted
    -
    Receive from Seat ECU
    Communication state of front power seat control switch LH signal / OK or Interpt
    OK: Communication is normal
    Interpt: Communication is interrupted
    -
    Receive from Combi
    Communication state of combination switch ECU signal / OK or Interpt
    OK: Communication is normal
    Interpt: Communication is interrupted
    -
    J/B
    Communication state of main body ECU signal / OK or Interpt
    OK: Communication is normal
    Interpt: Communication is interrupted
    -
    B/B
    Communication state of optional after parts ECU signal / OK or Interpt
    OK: Communication is normal
    Interpt: Communication is interrupted
    -
    The Number of DTCs
    Number of diagnostic trouble codes / min.: 0, max.: 255
    Actual number of diagnostic trouble codes
    -