Home › Engine / Hybrid System ยท 3UR-FBE › FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket and install it to the fuel tank.



    A194658E01
  1. Align the protrusion of the fuel suction with pump and gauge tube assembly with the groove of the fuel tank.

  1. Install the fuel suction with pump and gauge tube assembly into the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube assembly, tighten the retainer one complete turn by hand.



    A259584E01
  1. Set SST on the retainer.

    SST
    09808-14030  

    HINT:
    1. Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.
    2. Securely attach the claws of SST to the protrusions of the retainer and fix SST in place.
    3. Install SST while pressing the claws of SST against the retainer (toward the center of SST).



    A259587E01
  1. Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank, as shown in the illustration.

    SST
    09808-14030  

    HINT:
    Fit the tips of SST onto the ribs of the retainer.



2. INSTALL FUEL PRESSURE SWITCHING VALVE ASSEMBLY


    A194657
    A118171E05
  1. Install the fuel pressure switching valve assembly with the 2 tube joint clips.

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.



3. INSTALL NO. 1 FUEL TANK HEAT INSULATOR


    A194634E01
  1. Install the No. 1 fuel tank heat insulator with the 4 clips and nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



4. INSTALL FUEL TANK RETURN TUBE


    A196279
    A118171E05
  1. Install the fuel tank return tube with the tube joint clip.

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.



5. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank on a transmission jack and raise the fuel tank assembly.



    A194632
  1. Connect the wire harness clamp, fuel pump connector and fuel pressure switching valve connector to the fuel tank assembly.

    NOTICE:
    Be careful not to cut the wirings.

  1. Raise the transmission jack.



    A152248
  1. Install the 2 fuel tank bands with the 2 pins and 2 clips.

  1. Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    A185652E02
  1. Connect the fuel tank breather tube to the fuel tank inlet pipe sub-assembly.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



    A185653
  1. Connect the vent line hose and push down on the retainer.

    NOTICE:
    1. Before connecting the hose, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.
    2. After connecting, check if the hose and the connector are securely connected by pulling on them.



    A185648
  1. Connect the fuel tank to filler pipe hose to the fuel tank assembly.



6. CONNECT FUEL TANK RETURN TUBE


A185654E02
  1. Connect the fuel tank return tube.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.



7. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A185655E02
  1. Connect the fuel tank main tube.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.



    A194631
  1. Connect the fuel pressure switching valve with the bolt.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



8. INSTALL FUEL TANK CAP


9. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the Techstream main switch on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check the fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
      If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the system.
      If there are fuel leaks, repair or replace parts as necessary.