Home › Engine / Hybrid System ยท 3UR-FE › FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. REMOVE FUEL TANK CAP


4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A185647E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Pinch and pull the main tube connector to disconnect the fuel tank main tube sub-assembly connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



5. DISCONNECT FUEL TANK RETURN TUBE


A185646E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Pinch and pull the return tube connector to disconnect the fuel tank return tube connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



6. REMOVE FUEL TANK ASSEMBLY


    A185648
  1. Disconnect the fuel tank to filler pipe hose from the fuel tank assembly.



    A185649
  1. Pull up the retainer and disconnect the vent line hose.



    A185650E01
  1. Detach the lock claw by lifting up the cover, as shown in the illustration.

  1. Disconnect the fuel tank breather tube from the fuel tank inlet pipe sub-assembly.



    A152248
  1. Set a mission jack underneath the fuel tank assembly.

  1. Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slowly lower the mission jack slightly.

    NOTICE:
    Be careful not to cut the wirings.



    A185651
  1. Disconnect the wire harness clamp from the fuel tank assembly.

  1. Disconnect the fuel pump connector and lower the mission jack.

    NOTICE:
    1. Before this procedure, check the connector for dirt, mud or other contamination.
    2. Do not use any tools in this procedure.



7. REMOVE NO. 1 FUEL TANK HEAT INSULATOR


A152249E01
  1. Remove the nut from the heat insulator.

  1. Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



8. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    A152246E01
  1. Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



    A259584E01
  1. Set SST on the retainer.

    SST
    09808-14030  

    HINT:
    1. Securely attach the claws of SST to the protrusion of the fuel pump gauge retainer and fix SST in place.
    2. Install SST while pressing the claws of SST against the fuel pump gauge retainer (towards the center of SST).



    A259581
  1. Using SST, loosen the retainer.

    SST
    09808-14030  

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank may result.
    2. While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.

    HINT:
    The protrusion of the retainer fit in the ends of SST.

  1. Remove the retainer.

  1. Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.