OCCUPANT CLASSIFICATION SYSTEM > TERMINALS OF ECU |
| CHECK OCCUPANT CLASSIFICATION ECU |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| W6-1 (+B) - W6-3 (GND)*1 P14-1 (+B) - P14-3 (GND)*2 | G - W-B*1 R - W-B*2 | Battery | Ignition switch ON | 11 to 14 V |
| W6-2 (DIA) - W6-3 (GND)*1 P14-2 (DIA) - P14-3 (GND)*2 | BR - W-B | Diagnosis (DLC3) | Ignition switch ON | Pulse generation |
| W6-3 (GND) - Body ground*1 P14-3 (GND) - Body ground*2 | W-B - Body ground | Ground | Always | Below 1 Ω |
| W6-4- (FSR-) - W6-3 (GND)*1 P14-4- (FSR-) - P14-3 (GND)*2 | B - W-B | Center airbag sensor communication ground line | Always | Below 1 Ω |
| W6-5 (BGND) - W6-3 (GND)*1 P14-5 (BGND) - P14-3 (GND)*2 | BE - W-B | Passenger side buckle switch ground line | Always | Below 1 Ω |
| W6-7 (IG) - W6-3 (GND)*1 P14-7 (IG) - P14-3 (GND)*2 | SB - W-B*1, *2 LG - W-B*4 | Power source (IGN fuse) | Ignition switch ON | 11 to 14 V |
| W6-8 (FSR+) - W6-4 (FSR-)*1 P14-8 (FSR+) - P14-4 (FSR-)*2 | W - B | Center airbag sensor communication line | Ignition switch ON | Pulse generation |
| W6-9 (BSW) - W6-5 (BGND)*1 P14-9 (BSW) - P14-5 (BGND)*2 | L - BE | Passenger side buckle switch line | Buckle switch ON | 0.12 to 0.18 A |
| Buckle switch OFF | 0.4 to 0.7 mA | |||
| W1-1 (SGD1) - W6-3 (GND)*1 W1-1 (SGD1) - P14-3 (GND)*2 | Y - W-B | Front occupant detection sensor LH ground line | Always | Below 1 Ω |
| W1-2 (SGD2) - W6-3 (GND)*1 W1-2 (SGD2) - P14-3 (GND)*2 | SB - W-B*1, *2 LG - W-B*4 | Front occupant detection sensor RH ground line | Always | Below 1 Ω |
| W1-3 (SGD3) - W6-3 (GND)*1 W1-3 (SGD3) - P14-3 (GND)*2 | L - W-B | Rear occupant detection sensor LH ground line | Always | Below 1 Ω |
| W1-4 (SGD4) - W6-3 (GND)*1 W1-4 (SGD4) - P14-3 (GND)*2 | W - W-B | Rear occupant detection sensor RH ground line | Always | Below 1 Ω |
| W1-11 (SVC1) - W1-1 (SGD1) | P - Y | Front occupant detection sensor LH power supply line | Ignition switch ON, load is applied to front occupant detection sensor LH | 4.5 to 5.1 V |
| W1-12 (SVC2) - W1-2 (SGD2) | BR - SB | Front occupant detection sensor RH power supply line | Ignition switch ON, load is applied to front occupant detection sensor RH | 4.5 to 5.1 V |
| W1-5 (SVC3) - W1-3 (SGD3) | R -L | Rear occupant detection sensor LH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor LH | 4.5 to 5.1 V |
| W1-6 (SVC4) - W1-4 (SGD4) | B - W | Rear occupant detection sensor RH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor RH | 4.5 to 5.1 V |
| W1-7 (SIG1) - W1-1 (SGD1) | BE - Y | Front occupant detection sensor LH signal line | Ignition switch ON, load is applied to front occupant detection sensor LH | Pulse generation |
| W1-8 (SIG2) - W1-2 (SGD2) | GR - SB*1, *2 GR - LG*4 | Front occupant detection sensor RH signal line | Ignition switch ON, load is applied to front occupant detection sensor RH | Pulse generation |
| W1-9 (SIG3) - W1-3 (SGD3) | G - L | Rear occupant detection sensor LH signal line | Ignition switch ON, load is applied to rear occupant detection sensor LH | Pulse generation |
| W1-10 (SIG4) - W1-4 (SGD4) | V - W | Rear occupant detection sensor RH signal line | Ignition switch ON, load is applied to rear occupant detection sensor RH | Pulse generation |