Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E190368E01


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver, hazard switch, glove box, etc.).
    C
    Illumination comes on for all components except steering pad switch and radio receiver assembly.
    D



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)


    E121218E23
  1. Disconnect the H54 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H54-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Remove the steering pad switch assembly connector (Click here).


    E138075E02

  1. Connect the positive (+) lead of the battery to terminal z12-5 (IL+2) and the negative (-) lead of the battery to terminal z12-8 (EAU) of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    C152441E09
  1. Remove the spiral cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z12-8 (EAU) - H54-4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    z12-5 (IL+2) - H54-12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read Precaution in the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)


    E190388E02
  1. Disconnect the I3 radio receiver assembly connector.

  1. Disconnect the H54 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-6 (SWG) - H54-4 (EAU)
    Always
    Below 1 Ω
    I3-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY)


  1. for 8 Speakers:



      E141019E65
    1. Disconnect the I1 radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I1-10 (ILL+) - Body ground
      Light control switch TAIL or HEAD
      11 to 14 V



  1. for 14 Speakers:



      E190369E01
    1. Disconnect the I4 radio receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      I4-2 (ILL+) - Body ground
      Light control switch TAIL or HEAD
      11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMBINATION METER)


  1. for 8 Speakers:



      E190391E01
    1. Disconnect the I2 radio receiver assembly connector.

    2. Disconnect the H37 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I2-5 (ILL-) - H37-37 (ILL-)
      Always
      Below 1 Ω
      I2-5 (ILL-) - Body ground
      Always
      10 kΩ or higher



  1. for 14 Speakers:



      E190310E02
    1. Disconnect the I4 radio receiver assembly connector.

    2. Disconnect the H37 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I4-12 (ILL-) - H37-37 (ILL-)
      Always
      Below 1 Ω
      I4-12 (ILL-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)