Home › Drivetrain · AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC Code
DTC Detection Condition
Trouble Area
P0722
All conditions below are detected 5 seconds or more continuously (2-trip detection logic)
(a) No signal from speed sensor SP2 is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal are sent
(b) Vehicle speed is 9 km/h (5.59 mph) or more
(c) Park/neutral position switch is OFF
  1. Open or short in speed sensor SP2 circuit
  2. Speed sensor SP2
  3. ECM
  4. Automatic transmission (clutch, brake or gear, etc.)
Inspect using an oscilloscope:
Check the waveform of the ECM connector.
C161208E05

Standard:
Refer to the illustration.

Item
Content
Terminal No. (Symbol)
D56-101 (SP2+) - D56-100 (SP2-)
Tool setting
2 V/DIV., 20 msec./DIV
Condition
Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gear shift point and the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.
If the ECM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P0722: Speed sensor SP2/Verify pulse input
Required Sensors/Components
Speed sensor (SP2)
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
Vehicle speed at vehicle speed sensor
9 km/h (5.59 mph) or more
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Speed sensor signal
No signal

COMPONENT OPERATING RANGE


Vehicle speed at output speed sensor
9 km/h (5.59 mph) or more

WIRING DIAGRAM


C155187E28


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the Techstream is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR SP2 INSTALLATION


    C159067E07
  1. Check the speed sensor SP2 installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR SP2
OK


2.INSPECT SPEED SENSOR SP2


    C159420E12
  1. Disconnect the D44 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR SP2 (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM)


    C159422E88
  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-101 (SP2+) - D56-100 (SP2-)
    20°C (68°F)
    560 to 680 Ω
    D56-101 (SP2+) - Body ground
    Always
    10 kΩ or higher
    D56-100 (SP2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)