Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly and front seat side airbag assembly condition (activated/not activated) with the passenger airbag ON/OFF indicator.

HINT:
Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will be on/off depending on the conditions listed below.


Front Passenger Seat Condition
Passenger Airbag ON/OFF Indicator
SRS Warning Light
ON Indicator
OFF Indicator
Vacant
OFF
OFF
OFF
Adult is seated.
ON
OFF
OFF
Child is seated.
OFF
ON
OFF
Child restraint system is set.
OFF
ON
OFF
Occupant classification system failure
OFF
ON
ON

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

HINT:
When the indicator is malfunctioning, if the SRS warning light is off, follow the procedures below as a DTC is not output. If the SRS warning light is on, a DTC is output. Troubleshoot for the output DTC.

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to ON, and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC.

OK:
After the primary check period, the SRS warning light goes off.

HINT:
The primary check is performed for approximately 6 seconds after the ignition switch is turned ON.



NG
GO TO DTC CHART (Click here)
OK


2.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    Zero point calibration is completed using the Techstream.



NG
Go to step 4
OK


3.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 4
OK

END 

4.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch off.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

    1. for Manual seat (Click here)
    2. for Power seat (Click here)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }


NEXT


5.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    Zero point calibration is completed using the Techstream.



NG
Go to step 7
OK


6.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 7
OK

END 

7.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, read the Data List (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant Detection 
      Tester Display
      Measure Item/Range
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Passenger side buckle switch / Set, Unset or NG
      Unset: Passenger side seat belt is unfastened
      Set: Passenger side seat belt is fastened
      NG: Passenger side seat belt is malfunctioning
      -

      OK:
      The Techstream display changed correctly according to the operation of buckle switch.



NG
Go to step 12
OK


8.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check that the connectors (on the occupant classification ECU side and 4 occupant classification sensors side) are not damaged.

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Replace the occupant classification ECU (Click here).


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    Zero point calibration is completed using the Techstream.


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END 

12.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.

  1. Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged.

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


13.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Replace the front seat inner belt RH (Click here).


NEXT


14.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform zero point calibration (Click here).

    OK:
    Zero point calibration is completed using the Techstream.


NEXT


15.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END