FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY |
| 1. REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR |
![]() |
Remove the 4 bolts.
Using a hammer handle, remove the actuator.
| 2. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY |
![]() |
Remove the 4 bolts.
Using a plastic-faced hammer, remove the differential tube.
| 3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST, tap out the oil seal.
| 4. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY |
![]() |
Using SST, remove the side gear inter shaft.
Remove the snap ring from the side gear inter shaft.
| 5. REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT |
![]() |
Using SST and a hammer, unstake the nut.
![]() |
Using SST to hold the companion, remove the nut.
| 6. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, remove the companion flange from the differential carrier.
| 7. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| 8. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 9. REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER |
![]() |
Remove the bolts B and front differential front support assembly LH.
Remove the bolts A.
Using a plastic-faced hammer, tap out the bearing retainer.
| 10. REMOVE DIFFERENTIAL CASE ASSEMBLY |
Remove the differential case from the differential carrier.
| 11. REMOVE DIFFERENTIAL DRIVE PINION |
Set the differential carrier to an overhaul stand as shown in the illustration.
![]() |
Using a press, press out the drive pinion.
| 12. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING |
Remove the bearing (inner race) from the differential carrier.
| 13. REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR |
![]() |
Remove the 2 bolts and oil deflector.
| 14. REMOVE FRONT DIFFERENTIAL UNION |
![]() |
Remove the front differential union from the differential carrier.
| 15. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press out the bearing (inner race).
| 16. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using a brass bar and hammer, tap out the bearing (outer race) and washer.
| 17. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING |
![]() |
Using SST and hammer, tap out the bearing (outer race).
| 18. REMOVE FRONT DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.
![]() |
Using SST and a press, press out the outer race and plate washer from the differential carrier.
| 19. REMOVE DIFFERENTIAL RING GEAR |
![]() |
Place matchmarks on the ring gear and differential case.
Remove the 12 bolts.
Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.
| 20. REMOVE FRONT DIFFERENTIAL CASE BEARING |
![]() |
Using SST, remove the 2 bearings (inner race).
| 21. DISASSEMBLE DIFFERENTIAL CASE |
![]() |
Using a pin punch and hammer, tap out the straight pin.
Remove these parts from the differential case assembly.
2 differential side gears
2 differential side gear thrust washers
Differential pinion shaft
2 differential pinion gears
2 differential pinion gear thrust washers
| 22. INSPECT DIFFERENTIAL GEAR KIT |
Check that there is no damage to the pinion gear and side gear.
If the pinion gear and/or side gear is damaged, replace the differential gear kit.
| 23. INSPECT FRONT DIFFERENTIAL CASE |
Check that the differential case is not damaged.
If the differential case is damaged, replace it.
| 24. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING |
![]() |
Using a brass bar and hammer, tap out the 2 bearings.
| 25. REMOVE DIFFERENTIAL CLUTCH HUB |
![]() |
Using a snap ring expander, remove the snap ring.
Remove the differential clutch hub.
| 26. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
![]() |
Using SST, tap out the oil seal.
| 27. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Using a plastic-faced hammer, tap out the side gear shaft.
| 28. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Using SST, a brass bar and press, press out the bearing.
| 29. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB |
![]() |
Check for wear and damage to the clutch hub and clutch sleeve.
If necessary, replace them.
Check that the clutch sleeve slides smoothly on the clutch hub.
| 30. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT |
![]() |
Check for wear and damage to the clutch hub and side gear inter shaft.
Check that the clutch sleeve slides smoothly on the side gear inter shaft.
| 31. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.