Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C181030E01
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum Runout:
    Runout
    Specified Condition
    Vertical runout
    0.1 mm (0.00394 in.)
    Lateral runout
    0.1 mm (0.00394 in.)

    If the runout is greater than the maximum, replace the companion flange.



2. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C181010E01
  1. Using SST, tap out the 2 differential side gear shaft oil seals.

    SST
    09308-00010  



3. REMOVE REAR DRIVE PINION NUT


    C181003E01
  1. Using SST and a hammer, unstake the rear drive nut.

    SST
    09930-00010  



    C181026E01
  1. Using SST to hold the rear drive pinion companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a socket wrench (30mm), remove the rear drive pinion nut.

    NOTICE:
    Install nuts on the bolts to protect them, as shown in the illustration.



4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C181017E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly from the rear differential carrier assembly.

    HINT:
    Use the propeller shaft installation nuts when mounting SST on the flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09955-03050  



5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C181008E01
  1. Using SST, remove the rear differential carrier oil seal.

    SST
    09308-10010  



6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C181009
  1. Remove the rear differential drive pinion oil slinger from the rear differential carrier assembly.



7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C180990E01
  1. Remove the bearing (inner race) from the differential carrier.

    SST
    09950-40011   (09951-04010, 09953-04020, 09952-04010, 09954-04010)
    09955-04110  
    09958-04020  



8. REMOVE REAR DIFFERENTIAL SIDE BEARING RETAINER


    C180991
  1. Remove the 12 bolts and 2 straight pin.

  1. Using a plastic-faced hammer, tap out the rear differential side bearing retainer.



9. REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY


    C180993
  1. Remove the differential case from the differential carrier.



10. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the differential case from the differential drive pinion.



11. REMOVE REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR


    C180994
  1. Remove the 2 bolts and rear differential breather plug oil deflector.



12. REMOVE REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG


    C181031
  1. Remove the rear differential carrier cover breather plug from the rear differential carrier.



13. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C116049E01
  1. Using SST and a press, press out the bearing (inner race).

    SST
    09950-00020  
    If the drive gear or ring gear is damaged, replace them as a set.



14. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C159337
  1. Using a brass bar and hammer, tap out the bearing (outer race) and washer.



15. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C181151E01
  1. Using SST and hammer, tap out the bearing (outer race).

    SST
    09950-70010   (09951-07100)
    09950-60020   (09952-06010, 09951-00680, 09951-00730)



16. REMOVE REAR DIFFERENTIAL CASE BEARING

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.



    C180996E01
  1. Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07150)



    C180998E01
  1. Using SST and a press, press out the outer race and plate washer from the differential carrier.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07150)



17. REMOVE FRONT DIFFERENTIAL CASE BEARING


    C181000E01
  1. Using SST, remove the 2 bearings (inner race).

    SST
    09950-60010   (09951-00390, 09951-00560, 09952-06010)
    09950-40011   (09951-04010, 09953-04020, 09952-04010, 09954-04010, 09957-04010, 09958-04011)
    09955-04120  

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.



18. REMOVE DIFFERENTIAL RING GEAR


    C181001E01
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 12 bolts.

  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.