FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY |
| 1. INSTALL FRONT AXLE DUST SEAL |
![]() |
Using SST and a press, press in a new dust seal to the outboard joint shaft assembly.
| 2. INSTALL FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST, a steel plate and press, press in a new dust cover to the inboard joint shaft.
| 3. INSTALL FRONT DRIVE SHAFT OUTBOARD JOINT BOOT |
Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.
Install the new outboard joint boot to the outboard joint shaft.
Pack the outboard joint shaft and boot with grease from the boot kit.
Install the outboard joint boot into the groove on the outboard joint shaft.
| 4. INSTALL FRONT AXLE NO. 2 OUTBOARD JOINT BOOT SETTING CLAMP |
Install the No. 2 outboard joint boot setting clamp onto the outboard joint boot.
![]() |
Using SST, pinch the clamp.
| 5. INSTALL FRONT AXLE NO. 1 OUTBOARD JOINT BOOT SETTING CLAMP |
Install the No. 1 outboard joint boot setting clamp onto the outboard joint boot.
![]() |
Using SST, pinch the clamp.
| 6. INSPECT AND ADJUST FRONT AXLE OUTBOARD JOINT BOOT SETTING CLAMP |
![]() |
Using SST, inspect and adjust the clearance of the boot setting clamps.
| Boot setting clamp | Clearance |
| Inside | 2.8 to 3.8 mm (0.110 to 0.150 in.) |
| Outside | 3.0 to 4.0 mm (0.118 to 0.157 in.) |
| 7. TEMPORARILY INSTALL FRONT DRIVE SHAFT INBOARD JOINT BOOT |
Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.
Temporarily install the new inboard joint boot to the outboard joint shaft.
| 8. INSTALL FRONT DRIVE SHAFT INBOARD JOINT SHAFT ASSEMBLY |
![]() |
Install the cage to the outboard joint shaft.
![]() |
Align the matchmarks and install the inner race onto the outboard joint shaft.
![]() |
Using a snap ring expander, install a new snap ring.
![]() |
Align the matchmarks placed before removal, and install the cage to the inner race.
![]() |
Install the 6 balls.
Pack the inboard joint shaft and boot with grease from the boot kit.
![]() |
Align the matchmarks placed before removal, and install the inboard joint shaft to the outboard joint shaft.
Install a new snap ring.
| 9. INSTALL FRONT DRIVE SHAFT INBOARD JOINT BOOT |
Install the inboard joint boot into the groove on the outboard joint shaft and inboard joint shaft.
![]() |
Check whether the drive shaft dimensions are within the following specifications.
| 10. INSTALL FRONT AXLE NO. 2 INBOARD JOINT BOOT SETTING CLAMP |
Install the No. 2 inboard joint boot setting clamp.
| 11. INSTALL FRONT AXLE NO. 1 INBOARD JOINT BOOT SETTING CLAMP |
Install the inboard joint boot setting clamp.
| 12. INSPECT AND ADJUST FRONT AXLE INBOARD JOINT BOOT SETTING CLAMP |
Inspect and adjust the clearance of the boot setting clamps.
| 13. INSTALL FRONT DRIVE INNER SHAFT OUTER SHAFT SNAP RING |
![]() |
Install a new snap ring onto the inboard joint shaft.
| 14. INSPECT FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Check whether the drive shaft dimensions are within the following specifications.
![]() |
Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.
Check for cracks, damage and grease leakage on the boot joint.