Home › Drivetrain ยท AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY


    C159283E01
  1. Install the differential support with the F and G bolts.

    Torque:
    100 N*m{ 1019 kgf*cm , 74 ft.*lbf }

  1. Using a jack, slowly raise the front differential carrier assembly to its installation position.

  1. Temporarily install the A, B, C, D and E bolts.

  1. Tighten the A bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }

  1. Tighten the B and C bolts.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }

  1. Tighten the D and E bolts.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }

  1. Connect the automatic disconnecting differential actuator hose.

  1. Connect the automatic disconnecting differential actuator connector.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Install the front drive shaft (Click here).



3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure as the LH side.



4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Install the front propeller shaft (Click here).



5. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil Type:
    Item
    Oil Type and Viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front Differential Capacity:
    Specified Condition
    2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 Imp. qts.)

    Rear Differential Capacity:
    Specified Condition
    1.50 to 1.60 liters (1.6 to 1.7 US qts., 1.3 to 1.4 Imp. qts.)

  1. for Rear Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }



6. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. Bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. Screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



7. INSTALL FRONT WHEEL
  1. Install the front wheels.

    1. for Aluminum wheel

    Torque:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }

    1. for Steel wheel

    Torque:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



8. INSPECT AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR
  1. Inspect the automatic disconnecting differential actuator .