Home › Drivetrain ยท A760F AUTOMATIC TRANSMISSION / TRANSAXLE › OIL COOLER

OIL COOLER > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.


    A215892E01

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.



2. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).



3. DISCONNECT WATER BY-PASS PIPE ASSEMBLY


C209353
  1. Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler to disconnect the water by-pass pipe.

    HINT:
    Use a container to catch any coolant which flows out of the water by-pass hoses.



4. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


C209354
  1. Disconnect the 2 No. 1 transmission oil cooler hoses from the transmission.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.

  1. Remove the 2 No. 1 transmission oil cooler hoses from the transmission oil cooler spacer.



    C209355E01
  1. Remove the 3 bolts and transmission oil cooler from the transmission oil cooler spacer.

  1. Remove the 2 O-rings from the grooves of the transmission oil cooler.



5. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


C209356
  1. Disconnect the No. 2 transmission oil cooler inlet hose and No. 2 transmission oil cooler outlet hose from the transmission oil thermostat.

  1. Disconnect the No. 2 transmission oil cooler inlet hose and No. 2 transmission oil cooler outlet hose from the oil cooler tube, and remove them.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.



    C209357
  1. Disconnect the 2 No. 1 transmission oil cooler hoses from the transmission.

  1. Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.

  1. Remove the 2 No. 1 transmission oil cooler hoses from the transmission oil thermostat.



    C209358E01
  1. Remove the 3 bolts and oil cooler from the transmission oil thermostat.

  1. Remove the 2 O-rings from the grooves of transmission oil cooler.



6. REMOVE OIL COOLER ACCESSORY ASSEMBLY (w/ Trailer Towing System)


    C209363
  1. Disconnect the 2 hoses from the No. 2 oil cooler tube.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.

  1. Detach the claw to open the No. 1 flexible hose clamp.

  1. Disconnect the 2 hoses from the oil cooler tube and remove the oil cooler accessory assembly.

    NOTICE:
    When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.



7. REMOVE COOLER CONDENSER ASSEMBLY (AIR COOLED OIL COOLER) (w/ Trailer Towing System)
  1. Remove the cooler condenser (Click here).



8. REMOVE NO. 2 OIL COOLER TUBE (w/ Trailer Towing System)


C209366E01
  1. Disconnect the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose from the cooler condenser.

  1. Remove the bolt and No. 2 oil cooler tube together with the 2 oil cooler hoses.

  1. Remove the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose from the No. 2 oil cooler tube.



9. REMOVE OIL COOLER TUBE (w/ Trailer Towing System)


C209365
  1. Remove the 2 bolts and oil cooler tube.