SFI SYSTEM > ECM Power Source Circuit |

| 1.INSPECT FUSES (AM2, IG2 MAIN, EFI NO. 1, IGN) |
![]() |
Remove the AM2 fuse, IG2 MAIN fuse, EFI NO. 1 fuse and IGN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| AM2 fuse | Always | Below 1 Ω |
| IG2 MAIN fuse | Always | Below 1 Ω |
| EFI NO. 1 fuse | Always | Below 1 Ω |
| IGN fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.INSPECT INTEGRATION RELAY (IG2, EFI MAIN) |
![]() |
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-8 | When no battery voltage is applied to terminals 1B-6 and 1B-7 | 10 kΩ or higher |
| 1C-1 - 1B-8 | When battery voltage is applied to terminals 1B-6 and 1B-7 | Below 1 Ω |
| 1C-1 - 1B-4 | When no battery voltage is applied to terminals 1B-2 and 1B-3 | 10 kΩ or higher |
| 1C-1 - 1B-4 | When battery voltage is applied to terminals 1B-2 and 1B-3 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-81 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the A27 and D56 ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A27-28 (IGSW) - D56-81 (E1) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (RELAY BLOCK - ECM, IGNITION SWITCH, BATTERY AND BODY GROUND) |
![]() |
Disconnect the A27 ECM connector.
Disconnect the H10 ignition switch connector.
Disconnect the cable from the battery positive (+) terminal.
Remove the AM2 fuse and integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A27-28 (IGSW) - 1B-8 | Always | Below 1 Ω |
| 1B-7 - Body ground | Always | Below 1 Ω |
| Positive (+) battery cable - 1C-1 | Always | Below 1 Ω |
| Positive (+) battery cable - AM2 fuse terminal 1 | Always | Below 1 Ω |
| H10-5 (AM2) - AM2 fuse terminal 2 | Always | Below 1 Ω |
| H10-6 (IG2) - 1B-6 | Always | Below 1 Ω |
| A27-28 (IGSW) or 1B-8 - Body ground | Always | 10 kΩ or higher |
| Positive (+) battery cable or AM2 fuse terminal 1 - Body ground | Always | 10 kΩ or higher |
| Positive (+) battery cable or 1C-1 - Body ground | Always | 10 kΩ or higher |
| H10-5 (AM2) or AM2 fuse terminal 2 - Body ground | Always | 10 kΩ or higher |
| H10-6 (IG2) or 1B-6 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT IGNITION SWITCH |
Inspect the ignition switch (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, BATTERY AND BODY GROUND) |
![]() |
Disconnect the A27 ECM connector.
Disconnect the cable from the battery positive terminal.
Remove the integration relay from the engine room relay block.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A27-3 (+B) - 1B-4 | Always | Below 1 Ω |
| A27-2 (+B2) - 1B-4 | Always | Below 1 Ω |
| A27-34 (MREL) - 1B-2 | Always | Below 1 Ω |
| 1C-1 - Positive (+) battery cable | Always | Below 1 Ω |
| 1B-3 - Body ground | Always | Below 1 Ω |
| A27-3 (+B) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| A27-2 (+B2) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| A27-34 (MREL) or 1B-2 - Body ground | Always | 10 kΩ or higher |
| 1C-1 or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||