Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM

AIR SUSPENSION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When an air suspension system malfunction is detected under normal control operation, the suspension control ECU will suspend the switch control of the height control operation.

    DTC No.
    Malfunction
    Fail-Safe
    Fail-Safe Deactivation Condition
    C1713
    C1714
    Height control sensor circuit
    1. If there is an error on only 1 side, the system continues vehicle height control.
    2. If errors occur on both sides, the system interrupts vehicle height control.
    Return to normal condition.
    C1715
    C1716
    C1717
    Acceleration sensor circuit
    Continues damping force control (8th step is lower limit)
    Return to normal condition.
    C1731
    C1732
    C1733
    C1734
    Absorber control actuator circuit
    Interrupts damping force control after moving to the 16th step.
    (Except malfunction actuator)
    Return to normal condition.
    C1745
    Exhaust solenoid valve circuit
    1. Auto mode:
      The system sets the target vehicle height to normal, performs vehicle height ascent control, and interrupts control.
    2. Manual mode:
      The system accepts a switch operation for ascent, provided that the vehicle height is below normal.
    3. Continues damping force control.
    Return to normal condition.
    C1746
    Gate solenoid valve circuit
    1. Interrupts vehicle height control.
    2. Continues damping force control.
    Return to normal condition.
    C1747
    Leveling solenoid valve circuit
    1. Interrupts vehicle height control.
    2. Continues damping force control.
    Return to normal condition.
    C1751
    AIR SUS relay circuit
    1. Auto mode:
      The system sets the target vehicle height to normal, performs vehicle height descent control, and interrupts control.
    2. Manual mode:
      The system accepts a switch operation for descent, provided that the vehicle height is above normal.
    3. Continues damping force control.
    Return to normal condition.
    C1752
    Lock in height control compressor motor
    1. Auto mode:
      The system sets the target vehicle height to normal, performs vehicle height descent control, and interrupts control.
    2. Manual mode:
      The system accepts a switch operation for descent, provided that the vehicle height is above normal.
    3. Continues damping force control.
    After interrupting for 70 minutes, restart the control.
    C1761
    Powered continuously or powered excessively in height control compressor motor
    1. Auto mode:
      Powered continuously the first time: When the target vehicle speed is set to normal or HI, and the vehicle height is higher than the target, the system performs vehicle height descent control and interrupts control.
      Powered continuously the second time: The system sets the target vehicle height to normal, effects vehicle height descent control, and interrupts control.
    2. Manual mode:
      When the compressor motor is powered continuously both the first and second times, the system accepts a switch operation for descent, provided that the vehicle height is above normal.
    3. Continues damping force control.
    After interrupting for 70 minutes, restart the control.
    C1762
    Powered continuously or powered excessively in exhaust solenoid valve
    1. Auto mode:
      The system sets the target vehicle height to normal, performs vehicle height ascent control, and interrupts control.
    2. Manual mode:
      The system accepts a switch operation for ascent, provided that the vehicle height is below normal.
    3. Continues damping force control.
    Return to normal condition.
    C1781
    Suspension control ECU
    Interrupts vehicle height control and damping force control.
    Return to normal condition.
    C1782
    Power voltage dropped
    1. The system interrupts vehicle height control only when there is an error in the +B power source.
    2. Interrupts damping force control
    Return to normal condition.
    C1783
    Vehicle speed sensor circuit
    1. Continues vehicle height control.
    2. Interrupts damping force control after moving to the 16th step.
    Return to normal condition.
    C1784
    Steering angle sensor
    1. Continues vehicle height control.
    2. Interrupts damping force control after moving to the 16th step.
    Return to normal condition.
    C1787
    Lateral acceleration sensor
    1. Continues vehicle height control.
    2. Interrupts the damping force of roll posture control.
    Return to normal condition.
    C1789
    Vehicle identification
    Continues vehicle height control.
    Return to normal condition.
    U0100
    CAN communication system
    Continues vehicle height control and damping force control.
    Return to normal condition.
    U0122
    CAN communication system
    1. Continues vehicle height control.
    2. Interrupts damping force control after moving to the 16th step.
    Return to normal condition.
    U0124
    CAN communication system
    1. Continues vehicle height control.
    2. Interrupts the damping force of roll posture control.
    Return to normal condition.
    U0126
    CAN communication system
    1. Continues vehicle height control.
    2. Interrupts damping force control after moving to the 16th step.
    Return to normal condition.
    U0140
    CAN communication system
    Continues vehicle height control and damping force control.
    Return to normal condition.