THEFT DETERRENT SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |

Disconnect the H1, H3, H4, DA, DB, DC and DD ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DB-13 (BECU) - Body ground | GR - Body ground | +B power source | Always | 11 to 14 V |
| DA-1 (ALTB) - Body ground | B - Body ground | +B power source | Always | 11 to 14 V |
| DD-62 (GND1, GND2) - Body ground | W-B - Body ground | Power ground | Always | Below 1 Ω |
| H4-24 (DCTY) - Body ground | BR - Body ground | Driver door courtesy switch | Driver door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H3-21 (PCTY) - Body ground | BE - Body ground | Front passenger door courtesy switch input | Front passenger door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| DC-2 (LCTY) - Body ground | G*1 - Body ground B*2 - Body ground | Rear left door courtesy switch input | Rear left door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H3-25 (RRCY) - Body ground | L - Body ground | Rear right door courtesy switch input | Rear right door CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H4-16 (HCTY) - Body ground | V - Body ground | Engine hood courtesy switch | Engine hood CLOSED → OPEN | 10 kΩ or higher → Below 1 Ω |
| H1-5 (KSW) - Body ground | LG - Body ground | Key unlock warning switch signal | No key is in ignition key cylinder | 10 kΩ or higher |
| Key is in ignition key cylinder | Below 1 Ω |
Reconnect the H1, H3, H4, DA, DB, DC and DD ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H1-4 (IND) - Body ground | P - Body ground | Security indicator signal | Security indicator illuminates (illuminates only for 60 sec. in alarm sounding state (it is blinking when system is in armed state)) | 3 to 5 V |
| H1-6 (SH) - Body ground | W - Body ground | Security horn signal | Armed state | Below 1 V |
| Security horn is sounding (theft deterrent system is in alarm sounding state) | Pulse generation | |||
| H2-4 (HAZ) - Body ground | BE - Body ground | Hazard warning light signal | Armed state | Below 1 V |
| Security horn is sounding (theft deterrent system is in alarm sounding state) | Pulse generation | |||
| H4-17 (GBS)* - Body ground | L - Body ground | Glass breakage sensor ECU signal | Armed state | Below 1 V |
| Glass breakage sensor ECU signal system is in alarm sounding state | Pulse generation | |||
| DB-1 (HORN) - Body ground | V - Body ground | Horn signal (low pitched and high pitched) | Armed state | Below 1 V |
| Horn is sounding | 11 to 14 V |
| CHECK BACK DOOR ECU |

Disconnect the V2 and V3 connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| V2-1 (BDR) - Body ground | SB - Body ground | BDR power supply | Always | 11 to 14 V |
| V2-7 (BECU) - Body ground | GR - Body ground | BECU power supply | Always | 11 to 14 V |
| V3-10 (BDCY) - V3-20 (CTYE) | P - R | Back door courtesy switch circuit | Back door is open | 10 kΩ or higher |
| V3-10 (BDCY) - V3-20 (CTYE) | P - R | Back door courtesy switch circuit | Back door is closed | Below 1 Ω |
| V3-15 (HSW+) - V3-24 (HSW-) | B - W | Back door opener switch signal circuit | Back door opener switch OFF | 10 kΩ or higher |
| V3-15 (HSW+) - V3-24 (HSW-) | B - W | Back door opener switch signal circuit | Back door opener switch ON | Below 1 Ω |
| V2-6 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |