WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative |

| 1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
Check the wireless door lock control system function (Click here).
| Result | Proceed to |
| The wireless door LOCK/UNLOCK function does not operate with transmitter | A |
| The power back door function does not operate with transmitter | B |
|
| ||||
| A | |
| 2.CHECK DOOR CONTROL TRANSMITTER |
When another registered door control transmitter is used, check that the wireless operates normally.
| Result | Proceed to |
| Wireless door LOCK/UNLOCK function operates and door control transmitter that did not operate is electrical key transmitter | A |
| Wireless door LOCK/UNLOCK function does not operate | B |
|
| ||||
| A | |
| 3.INSPECT TRANSMITTER BATTERY (VOLTAGE) |
Electrical key transmitter
![]() |
Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
![]() |
Using an oscilloscope, check the transmitter battery voltage waveform.
| Item | Content |
| Tester Connection | Battery positive (+) - Battery negative (-) |
| Tool Setting | 0.5 V/DIV., 100 ms/DIV. |
| Condition | Ignition switch OFF, all doors closed and lock switch pushed |
| Specified Condition | 2.2 to 3.2 V (Refer to the waveform) |
|
| ||||
| OK | ||
| ||
| 4.CHECK ROOM LIGHT ASSEMBLY |
Check that the room light illumination operates normally.
|
| ||||
| OK | |
| 5.SWITCH TO SELF-DIAGNOSTIC MODE |
![]() |
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.
Within 30 seconds of turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.
Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.
|
| ||||
| OK | |
| 6.CHECK BY SELF DIAGNOSTIC MODE |

Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.
| Result | Proceed to |
| Unmatching recognition code is output | A |
| Normal waves (light flash patterns) is output | B |
| No diagnosis outputs | C |
|
| ||||
|
| ||||
| A | |
| 7.REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).
|
| ||||
| OK | ||
| ||
| 8.CHECK DOOR CONTROL RECEIVER (RESPONSE) |
Prepare the door control transmitter of another vehicle.
Hold down the door control transmitter switch.
Check that an unmatching recognition code is output.
|
| ||||
| OK | ||
| ||
| 9.REPLACE DOOR CONTROL RECEIVER |
Temporarily replace the door lock control receiver with a new or normally functioning one (Click here).
| NEXT | |
| 10.REGISTER RECOGNITION CODE |
Perform the registration procedures (Click here).
| NEXT | |
| 11.CHECK DOOR CONTROL RECEIVER (OPERATION) |
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
|
| ||||
| OK | ||
| ||
| 12.INSPECT UNLOCK WARNING SWITCH |
![]() |
Remove the unlock warning switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Free | 10 kΩ or higher |
| Pushed | Below 1 Ω |
Reconnect the unlock warning switch.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND) |
![]() |
Disconnect the H21 unlock warning switch connector.
Disconnect the H1 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H21-1 - H1-5 (KSW) | Always | Below 1 Ω |
| H21-2 - Body ground | ||
| H1-5 (KSW) or H21-1 - Body ground | Always | 10 kΩ or higher |
Reconnect the unlock warning switch connector.
Reconnect the main body ECU connector
|
| ||||
| OK | |
| 14.INSPECT DOOR CONTROL RECEIVER (OUTPUT) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O25-2 (RDA) - Body ground | Transmitter switch not pressed → pressed (No key in ignition key cylinder, all doors closed) | 11 to 14 V → Pulse generation |
|
| ||||
| OK | ||
| ||
| 15.REPLACE DOOR CONTROL TRANSMITTER |
Temporarily replace the door control transmitter module with a new or normally functioning one.
| NEXT | |
| 16.REGISTER RECOGNITION CODE |
Perform the registration procedures (Click here).
| NEXT | |
| 17.CHECK DOOR CONTROL TRANSMITTER MODULE |
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
|
| ||||
| OK | ||
| ||