Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)

H100802E08

  1. Disconnect the O30 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-12 (B) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    O30-10 (ECUB) - Body ground
    R - Body ground
    ECUB power supply
    Always
    11 to 14 V
    O30-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    O30-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    O30-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O30 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O30-2 (DC+) - O30-1 (DC-)
    P - SB
    Back door lock motor circuit
    Back door lock motor is operating
    11 to 14 V
    O30-2 (DC+) - O30-1 (DC-)
    P - SB
    Back door lock motor circuit
    Back door lock motor is not operating
    Below 1 V
    O30-20 (FUL) - Body ground
    R - Body ground
    Back door courtesy switch circuit
    Back door is closed
    11 to 14 V
    O30-20 (FUL) - Body ground
    R - Body ground
    Back door courtesy switch circuit
    Back door is open
    Below 1 V
    O30-22 (HAF) - Body ground
    V - Body ground
    Back door lock half-latch switch signal circuit
    Back door is open → Back door closer motor operating → Back door is closed
    Below 1 V → 11 to 14 V → Below 1 V
    O30-24 (POS) - Body ground
    BE - Body ground
    Back door lock position switch signal circuit
    Back door is open → Back door closer operating → Back door is closed
    Below 1 V → 11 to 14 V → Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C172609E07

  1. Disconnect the DA and DD connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    B - Body ground
    ALTB power supply
    Always
    11 to 14 V
    DD-62 (GND1,GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK BACK DOOR ECU

B193574E01

  1. Disconnect the V2 and V3 connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    SB - Body ground
    BDR power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    GR - Body ground
    BECU power supply
    Always
    11 to 14 V
    V3-10 (BDCY) - V3-20 (CTYE)
    P - R
    Back door courtesy switch circuit
    Back door is open
    Below 1 Ω
    V3-10 (BDCY) - V3-20 (CTYE)
    P - R
    Back door courtesy switch circuit
    Back door is closed
    10 kΩ or higher
    V3-15 (HSW+) - V3-24 (HSW-)
    B - W
    Back door opener switch signal circuit
    Back door opener switch OFF
    10 kΩ or higher
    V3-15 (HSW+) - V3-24 (HSW-)
    B - W
    Back door opener switch signal circuit
    Back door opener switch ON
    Below 1 Ω
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.