POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU |
| CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |

Disconnect the M3 power window regulator motor LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M3-2 (B) - Body ground | G - Body ground | Battery power supply | Always | 11 to 14 V |
| M3-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the M3 power window regulator motor LH connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M3-10 (UP) - M3-1 (GND) | BE - W-B | Power window UP operation | Ignition switch ON Power window regulator master switch OFF → UP | 11 to 14 V → Below 1 V |
| M3-10 (UP) - M3-1 (GND) | BE - W-B | Power window UP operation | Ignition switch ON door glass fully open → power window AUTO UP operation → the door glass fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| M3-7 (DOWN) - M3-1 (GND) | LG - W-B | Power window DOWN operation | Ignition switch ON Power window regulator master switch OFF → DOWN | 11 to 14 V → Below 1 V |
| M3-7 (DOWN) - M3-1 (GND) | LG - W-B | Power window DOWN operation | Ignition switch ON door glass fully closed → power window AUTO DOWN operation → the door glass fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| M3-9 (LIN) - M3-1 (GND) | W - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| CHECK FRONT POWER WINDOW REGULATOR MOTOR RH |

Disconnect the L3 power window regulator motor RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L3-2 (B) - Body ground | V - Body ground | Battery power supply | Always | 11 to 14 V |
| L3-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the L3 power window regulator motor RH connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| L3-10 (UP) - L3-1 (GND) | G - W-B | Power window UP operation | Ignition switch ON power window regulator switch OFF → UP | 11 to 14 V → Below 1 V |
| L3-10 (UP) - L3-1 (GND) | G - W-B | Power window UP operation | Ignition switch ON door glass fully open → power window AUTO UP operation → the door glass fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| L3-7 (DOWN) - L3-1 (GND) | P - W-B | Power window DOWN operation | Ignition switch ON power window regulator switch OFF → DOWN | 11 to 14 V → Below 1 V |
| L3-7 (DOWN) - L3-1 (GND) | P - W-B | Power window DOWN operation | Ignition switch ON door glass fully closed → power window AUTO DOWN operation → the door glass fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| L3-9 (LIN) - L3-1 (GND) | L - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| L3-4 (AUTO) - L3-1 (GND) | B - W-B | Power window AUTO UP/DOWN operation | Ignition switch ON power window regulator switch OFF → AUTO UP/DOWN operation | 11 to 14 V → Below 1 V |
| CHECK POWER WINDOW REGULATOR MASTER SWITCH |

Disconnect the M2 power window regulator master switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-3 (B) - Body ground | L - Body ground | Battery power supply | Ignition switch ON | 11 to 14 V |
| M2-13 (B) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| M2-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the M2 power window regulator master switch connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-4 (UP) - M2-1 (E) | BE - W-B | Driver side door power window UP operation | Ignition switch ON, driver side door power window regulator switch OFF → UP | 11 to 14 V → Below 1 V |
| M2-4 (UP) - M2-1 (E) | BE - W-B | Driver side door power window AUTO UP operation | Ignition switch ON, driver side door glass fully closed → power window AUTO UP operation → driver side door glass fully open | 11 to 14 V → Below 1 V → 11 to 14 V |
| M2-5 (DOWN) - M2-1 (E) | LG - W-B | Driver side door power window DOWN operation | Ignition switch ON, driver side door power window regulator switch OFF → DOWN | 11 to 14 V → Below 1 V |
| M2-5 (DOWN) - M2-1 (E) | LG - W-B | Driver side door power window AUTO DOWN operation | Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open | 11 to 14 V → Below 1 V → 11 to 14 V |
| M2-12 (U) - M2-1 (E) | V - W-B | Rear LH side door power window UP operation | Ignition switch ON, rear LH side door power window regulator switch OFF → UP | Below 1 V → 11 to 14 V |
| M2-15 (D) - M2-1 (E) | B - W-B | Rear LH side door power window DOWN operation | Ignition switch ON, rear LH side door power window regulator switch OFF → DOWN | Below 1 V → 11 to 14 V |
| M2-10 (U) - M2-1 (E) | BE - W-B | Rear RH side door power window UP operation | Ignition switch ON, rear RH side door power window regulator switch OFF → UP | Below 1 V → 11 to 14 V |
| M2-16 (D) - M2-1 (E) | LG - W-B | Rear RH side door power window DOWN operation | Ignition switch ON, rear RH side door power window regulator switch OFF → DOWN | Below 1 V → 11 to 14 V |
| M2-6 (LIN1) - M2-1 (E) | L - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| M2-7 (LIN2) - M2-1 (E) | W - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |

Disconnect the DA, DB, DD, H2, H3 and H4 main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DD-62 (GND1, GND2) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| H3-21 (PCTY) - Body ground | BE - Body ground | Front door courtesy light switch RH signal | Front door RH open → closed | Below 1 Ω → 10 kΩ or higher |
| H4-24 (DCTY) - Body ground | BR - Body ground | Front door courtesy light switch LH signal | Front door LH open → closed | Below 1 Ω → 10 kΩ or higher |
Reconnect the DA, DB, DD, H2, H3 and H4 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DB-13 (BECU) - Body ground | GR - Body ground | BECU power supply | Always | 11 to 14 V |
| DA-1 (IG) - Body ground | B - Body ground | IG signal | Always | 11 to 14 V |
| H2-10 (LIN2) - DD-62 (GND1, GND2) | V - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| CHECK BACK DOOR ECU (MULTIPLEX BODY ECU) |

Disconnect the V2 and V3 back door ECU connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| V2-7 (BECU) - Body ground | GR - Body ground | Battery power supply | Always | 11 to 14 V |
| V2-8 (SIG) - Body ground | Y - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| V2-6 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| V3-7 (BKUL) - V3-19 (KEYE) | LG - BE | Back door key cylinder linked switch signal | Back door key cylinder turned UNLOCK | Below 1 Ω |
| V3-8 (BKL) - V3-19 (KEYE) | G - BE | Back door key cylinder linked switch signal | Back door key cylinder turned LOCK | Below 1 Ω |
| V3-17 (P) - V3-25 (SGND) | V - G | Rear wiper retractable position switch signal | Rear wiper motor retractable position | Below 1 Ω |
Reconnect the V2 and V3 back door ECU connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| V2-16 (MPX1) - V2-6 (GND) | Y - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| V2-21 (A UP) - V2-6 (GND) | G - W-B | Back door power window AUTO UP signal | Ignition switch ON Back door power window switch OFF → AUTO UP | Pulse generation → Below 1 V |
| V2-22 (BUP) - V2-6 (GND) | BE - W-B | Back door power window UP signal | Ignition switch ON Back door power window switch OFF → UP | Pulse generation → Below 1 V |
| V2-23 (BDN) - V2-6 (GND) | V - W-B | Back door power window DOWN signal | Ignition switch ON Back door power window switch OFF → DOWN | Pulse generation → Below 1 V |
| V2-24 (A DN) - V2-6 (GND) | L - W-B | Back door power window AUTO DOWN signal | Ignition switch ON Back door power window switch OFF → AUTO DOWN | Pulse generation → Below 1 V |
| V3-5 (BDUP) - V2-6 (GND) | BE - W-B | Back door power window UP operation signal | Ignition switch ON Back door power window switch OFF → UP | Below 1 V → 11 to 14 V |
| V3-6 (BDDN) - V2-6 (GND) | P - W-B | Back door power window DOWN operation signal | Ignition switch ON Back door power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| V3-12 (DSV) - V3-23 (DSG) | LG - SB | Power supply for Hall-IC | Ignition switch ON | 8.5 to 16 V |
| V3-13 (DS1) - V3-23 (DSG) | L - SB | Back door window glass position signal | Back door power window operation | Pulse generation |
| V3-14 (DS2) - V3-23 (DSG) | Y - SB | Back door window glass position signal | Back door power window operation | Pulse generation |
| V3-19 (KEYE) - V2-6 (GND) | BE - W-B | Ground for back door key cylinder switch | Always | Below 1 Ω |
| V3-23 (DSG) - V2-6 (GND) | SB - W-B | Ground for Hall-IC | Always | Below 1 Ω |
| V3-25 (SGND) - V2-6 (GND) | G - W-B | Ground for rear wiper reverse position and rear wiper retractable position switch | Always | Below 1 Ω |