Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT

REAR AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL REAR COOLING UNIT ASSEMBLY


    E190306E01
  1. Install the rear cooling unit with the 3 bolts and nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    Tighten the bolts in the order shown in the illustration.



    E188150
  1. Connect the 3 connectors.

  1. Attach the 3 clamps.



2. INSTALL FOLD SEAT CONTROL ECU


    B194058
  1. Install the fold seat control ECU with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 connectors.



3. INSTALL AMPLIFIER ANTENNA ASSEMBLY


    I104304
  1. Install the amplifier antenna with the bolt.



4. INSTALL REAR SIDE NO. 1 AIR DUCT


    I104303
  1. Install the air duct with the clip.

  1. Attach the clamp.



5. INSTALL COVER SUB-ASSEMBLY


    I104302
  1. Attach the 2 claws and install the cover.



6. INSTALL QUARTER TRIM BRACKET RH


    I104301
  1. Install the quarter trim bracket with the 2 bolts.

  1. Attach the clamp.



7. INSTALL REAR SIDE NO. 2 AIR DUCT


    E188149
  1. Install the air duct with the 2 clips.



8. INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH


9. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


B190123
  1. Engage the 5 clips to install the rear window No. 2 side garnish assembly RH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193067
  1. Engage the claw to install the cover.



10. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard)
  1. Connect the connector.

  1. Engage the 11 clips to install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B219907



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



11. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
  1. Connect the 3 connectors.

  1. Engage the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222459



    B190147
  1. Engage the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



12. INSTALL REAR FLOOR MAT SUPPORT PLATE


B190142
  1. Engage the 5 clips to the 4 claws, and install the rear floor mat support plate.



13. INSTALL ROPE HOOK ASSEMBLY


B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws to install the cover.



14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



15. INSTALL REAR DOOR SCUFF PLATE RH


B186666
  1. Engage the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Engage the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the screw.



16. INSTALL REAR FLOOR STEP NO. 1 COVER


B191404
  1. Engage the 2 claws to install the rear floor step No. 1 cover.



17. INSTALL REAR FLOOR STEP NO. 2 COVER


B193890
  1. Engage the 2 claws to install the rear floor step No. 2 cover.



18. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


B191794
  1. Engage the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.



19. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
  1. Install the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



    B191204
  1. Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.

  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }

  1. Connect the seat wire connector.



    B191200
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



20. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
  1. Install the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



    B191202
  1. Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.

  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



    B191200
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



21. INSTALL SEAT TRACK BRACKET FRONT COVER INNER


    B232093E01
  1. Attach the 2 guides and claw and clip in the order shown in the illustration, and then install the seat track bracket front cover inner.



22. INSTALL SEAT TRACK BRACKET FRONT COVER OUTER


    B191197E02
  1. Attach the 2 guides and 2 claws in the order shown in the illustration, and then install the seat track bracket front cover outer.



23. INSTALL DECK BOARD BRACKET


B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



24. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



25. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


B190117
  1. Engage the 5 clips to install the No. 1 deck board.



26. INSTALL ROPE HOOK ASSEMBLY


B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



27. INSTALL LUGGAGE COMPARTMENT TRIM BOX


B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



28. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


B194608
  1. Engage the 4 guides to install the No. 2 deck board.



29. CONNECT COOLER REFRIGERANT LIQUID PIPE D
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant liquid pipe.

  1. Install the cooler refrigerant liquid pipe.



30. CONNECT COOLER REFRIGERANT SUCTION PIPE B
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant suction pipe.

  1. Move the hook connector in the direction indicated by the arrow in the illustration.



    I104453
  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



31. CONNECT HEATER WATER HOSE OUTLET E


    I104298E01
  1. Connect the water hose onto the cooling unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



32. CONNECT HEATER WATER HOSE INLET H


    I104296E01
  1. Connect the water hose onto the cooling unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



33. ADD ENGINE COOLANT (for 1UR-FE)
  1. Add engine coolant.

    Standard Capacity:
    14.8 liters (15.6 US qts, 13.0 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



34. ADD ENGINE COOLANT (for 3UR-FE)
  1. Add engine coolant.
    Standard Capacity 
    Item
    Specified Condition
    w/ Trailer Towing System
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)
    w/o Trailer Towing System
    13.7 liters (14.5 US qts., 12.0 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



35. ADD ENGINE COOLANT (for 3UR-FBE)
  1. Add engine coolant.
    Standard Capacity 
    Item
    Specified Condition
    w/ Trailer Towing System
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)
    w/o Trailer Towing System
    13.7 liters (14.5 US qts., 12.0 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



36. INSPECT FOR COOLANT LEAK (for 1UR-FE)


37. INSPECT FOR COOLANT LEAK (for 3UR-FE)


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



38. INSPECT FOR COOLANT LEAK (for 3UR-FBE)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161766E02
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



39. CHARGE REFRIGERANT



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    860 to 920 g (30.3 to 32.5 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I103968E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



40. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



41. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



42. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. Bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. Screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }