Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT

REAR AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL REAR EVAPORATOR SUB-ASSEMBLY


    E150109
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the rear evaporator.



    I104331
  1. Install the rear evaporator as shown in the illustration.

    HINT:
    If a new rear evaporator is installed, add compressor oil to the rear evaporator as follows.

    Compressor oil:
    ND-OIL8 or equivalent. Add 40 cc (1.35 fl. oz.)



    I104329
  1. Install the 13 screws.



2. INSTALL REAR EVAPORATOR TEMPERATURE SENSOR


    I104328
  1. Attach the claw and install the rear evaporator temperature sensor.

  1. Attach the clamp to the rear cooling unit.



3. INSTALL REAR COOLING UNIT EXPANSION VALVE


    E150105
  1. Using a 4 mm hexagon wrench, install the rear cooling unit expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



    I104327
  1. Install the grommet.



    I104326
  1. Attach the 3 claws and install the plate.



4. INSTALL BLOWER MOTOR CONTROL


    I104325
  1. Install the blower motor controller with the 2 screws.



5. INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY


    I104324
  1. Install the rear blower motor with the 3 screws.



6. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


    E183891
  1. Install the heater radiator unit as shown in the illustration.



    E183889
  1. Attach the claw and install the heater clamp.

  1. Install the heater clamp with the screw.



7. INSTALL HEATER WATER OUTLET HOSE


    E183888
  1. Using pliers, grip the claws of the clip and slide the clips to connect the heater water hose.



8. INSTALL HEATER WATER INLET HOSE


    E183887
  1. Using pliers, grip the claws of the clip and slide the clips to connect the heater water hose.



9. INSTALL WATER PIPE SUB-ASSEMBLY


E183739
  1. Using pliers, grip the claws of the 2 clips and slide the clips to install the water pipe.



    I104317
  1. Install the bracket with the 4 screws.



10. INSTALL AIRCONDITIONER CONNECTOR TUBE
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the air conditioning connector tube.

    Compressor oil:
    ND-OIL 8 or equivalent



    I104316
  1. Install the 2 new O-rings on the air conditioning connector tube.



    I104315
  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    I104313
  1. Install the air conditioning connector tube with the 3 screws.

  1. Connect the hose.



    I104312
  1. Install the packing.



11. INSTALL REAR MODE DAMPER SERVO MOTOR SUB-ASSEMBLY


    I104311E01
  1. Using the reference point, install the rear mode damper servo motor with the 2 screws.

  1. Connect the connector.



    E191234
  1. Install the bracket with the 4 screws.



12. INSTALL REAR AIR MIX DAMPER SERVO MOTOR SUB-ASSEMBLY


    I104308E01
  1. Using the reference point, install the rear air mix control servo motor with the 2 screws.

  1. Connect the connector.