Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM

DTC    B2251    Back Door Closer Switch Malfunction

for Preparation Click here


DESCRIPTION

The power back door drive unit (power back door ECU) inputs signals from the full-latch switch, sector switch and back door courtesy light switch, which are built into the back door lock. Based on these switch signals, the latch position of the back door lock is determined.

DTC No.
DTC Detection Condition
Trouble Area
B2251
While back door closer is operating, malfunction is detected in position information from each switch within specified amount of time.
  1. Back door lock
  2. Wire harness
  3. Power back door ECU

WIRING DIAGRAM


B189795E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (HALF LATCH SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door / Data List /

  1. According to the display on the Techstream, read the Data List.

    Back Door (Power Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Half Latch SW
    Latch switch signal / ON or OFF
    ON: Back door lock motor is open-latch or over-latch
    OFF: Back door lock motor is full-latch or half-latch
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 10
OK


2.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door / Data List /

  1. According to the display on the Techstream, read the Data List.

    Back Door (Power Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Courtesy SW
    Back door courtesy light switch signal / ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 3
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)  

3.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - POWER BACK DOOR ECU)
B191746E01
  1. Disconnect the V2 back door ECU connector.

  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V2-17 (OCTY) - O30-20 (FUL)
    Always
    Below 1 Ω
    V2-17 (OCTY) or O30-20 (FUL) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back door ECU connector.

  1. Reconnect the power back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING BACK DOOR ECU (BACK DOOR COURTESY LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door P/W / Data List /

  1. According to the display on the Techstream, read the Data List.

    Back Door P/W (Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy SW
    Back door courtesy light switch signal / ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 5
OK

REPLACE BACK DOOR ECU (Click here)  

5.INSPECT BACK DOOR LOCK (BACK DOOR COURTESY LIGHT SWITCH)

B191744E02

  1. Remove the back door lock (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    6 (S) - 3 (E)
    Open-latch
    Below 1 Ω
    6 (S) - 3 (E)
    Half-latch
    Below 1 Ω
    6 (S) - 3 (E)
    Full-latch
    10 kΩ or higher
    6 (S) - 3 (E)
    Over-latch
    10 kΩ or higher



NG
REPLACE BACK DOOR LOCK (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - BACK DOOR ECU AND BODY GROUND)


    B191745E01
  1. Disconnect the V5 door lock connector.

  1. Disconnect the V2 and V3 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V5-6 (S) - V3-10 (BDCY)
    Always
    Below 1 Ω
    V5-3 (E) - V3-20 (CTYE)
    Always
    Below 1 Ω
    V2-6 (GND) - Body ground
    Always
    Below 1 Ω
    V5-6 (S) or V3-10 (BDCY) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the door lock and ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE POWER BACK DOOR DRIVE UNIT
  1. Temporarily replace the power back door drive unit with a new or normally functioning one (Click here).


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Check the DTCs (Click here).

    OK:
    DTC not output B2251.



NG
REPLACE BACK DOOR ECU (Click here)
OK

END (POWER BACK DOOR DRIVE UNIT DEFECTIVE) 

10.INSPECT BACK DOOR LOCK (LATCH SWITCH)

B191744E05

  1. Remove the back door lock (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Latch Switch
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    5 (CLS) - 3 (E)
    Open-latch
    Below 1 Ω
    5 (CLS) - 3 (E)
    Half-latch
    10 kΩ or higher
    5 (CLS) - 3 (E)
    Full-latch
    10 kΩ or higher
    5 (CLS) - 3 (E)
    Over-latch
    Below 1 Ω



NG
REPLACE BACK DOOR LOCK (Click here)
OK


11.CHECK HARNESS AND CONNECTOR


    B191749E04
  1. Disconnect the V5 door lock connector.

  1. Disconnect the O30, V2 and V3 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V5-3 (E) - V3-20 (CTYE)
    Always
    Below 1 Ω
    V5-5 (CLS) - O30-22 (HAF)
    Always
    Below 1 Ω
    V2-6 (GND) - Body ground
    Always
    Below 1 Ω
    V5-5 (CLS) or O30-22 (HAF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the door lock and ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)