Home › Engine / Hybrid System ยท 3UR-FE › COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151835E01

  1. Tighten the radiator drain cock plug by hand.



3. REMOVE FRONT BUMPER COVER ASSEMBLY
  1. Remove the front bumper cover assembly (Click here).



4. REMOVE NO. 1 FRONT BUMPER SIDE RETAINER SUB-ASSEMBLY RH (for Condenser with Separate Oil Cooler)


5. REMOVE OIL COOLER ASSEMBLY (for Condenser with Separate Oil Cooler)


    A162471
  1. Remove the 5 nuts and oil cooler from the oil filter bracket.



    A162475
  1. Remove the 2 O-rings.



6. REMOVE V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



7. REMOVE INLET RADIATOR HOSE


    A183232
  1. Remove the inlet radiator hose.



8. DISCONNECT OUTLET RADIATOR HOSE


    A183247
  1. Disconnect the outlet radiator hose from the water inlet housing.



9. REMOVE FAN SHROUD


    A151842
  1. Loosen the 4 nuts holding the fluid coupling and fan.

  1. Remove the fan and generator V belt .



    A161784
  1. for Condenser with Separate Oil Cooler:
    Detach the claw to open the No. 1 flexible hose clamp.



    A183235
  1. Disconnect the reservoir hose from the upper radiator tank.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



10. REMOVE RADIATOR SIDE DEFLECTOR RH


    A232101E01
  1. Remove the 6 clips and side deflector.



11. REMOVE RADIATOR SIDE DEFLECTOR LH


    A215584
  1. Remove the 6 clips and side deflector.

  1. Disconnect the wire harness clamp.



12. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL (for LH Side)


    A183237
  1. Remove the 3 clips and remove the No. 1 radiator to support seal.



13. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL (for RH Side)


    A183236
  1. Remove the 3 clips and remove the No. 1 radiator to support seal.



14. REMOVE RADIATOR ASSEMBLY


    A183239
  1. Remove the 4 bolts and radiator.



15. REMOVE OUTLET RADIATOR HOSE


    A183240
  1. Remove the outlet radiator hose from the radiator.