Home › Engine / Hybrid System ยท 3UR-FBE › ENGINE MECHANICAL › ENGINE

ENGINE > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT ENGINE COOLANT
(Click here)


2. INSPECT ENGINE OIL
(Click here)


3. INSPECT BATTERY

NOTICE:
If the battery is weak or if the engine is difficult to start, perform the following procedures.

  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the electrolyte quantity of each cell.

    1. For maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, replace the battery.
      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

        HINT:
        Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

    2. For non-maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte's specific gravity.

        Standard specific gravity:
        1.25 to 1.29 at 20°C (68°F)

      1. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

        HINT:
        Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

  1. Turn the ignition switch off and turn on the headlight for 20 to 30 seconds. This will remove the surface charge from the battery.



    A001260E02
  1. Measure the battery voltage between the negative (-) and positive (+) terminals of the battery.

    Standard voltage:
    12.5 to 12.9 V at 20°C (68°F)

    If the voltage is below the specification, recharge the battery.



    Z011580E03
  1. Reference:
    The indicator shows the battery condition.

    HINT:
    1. Blue: OK
    2. White: Charging necessary
    3. Red: Insufficient electrolyte



4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air filter is not excessively damaged or oily.
    If necessary, replace the air filter.



5. INSPECT SPARK PLUG
(Click here)


6. INSPECT FAN & GENERATOR V BELT


A163769E01
  1. Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the fan and generator V belt.

    1. The belt is cracked.
    2. The belt is worn out to the extent that the cords are exposed.
    3. The belt has chunks missing from the ribs.

  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the groove on the bottom to the pulley. If it has slipped out, replace the fan and generator V belt. Install a new fan and generator V belt correctly.



7. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
  1. Check that nothing gets caught in the tensioner by turning it clockwise and counterclockwise. If a malfunction exists, replace the tensioner.



8. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Start the engine and idle it.

    3. Turn the Techstream main switch on.

    4. Enter the following menus: Select: Powertrain / Engine and ECT / Data List / IGN Advance.

      HINT:
      Refer to the Techstream operator manual for further details.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    5. Disconnect the Techstream from the DLC3.



    A160842
  1. When not using the Techstream:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.



    2. A178528E01
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C before connecting the terminals.



    4. A160843
    5. Using the timing light, check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    6. Remove SST from the DLC3.

    7. Check the ignition timing.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)

    8. Disconnect the timing light from the engine.



9. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the Techstream.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Turn the Techstream main switch on.

    4. Enter the following menus: Select: Powertrain / Engine and ECT / Data List / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      HINT:
      Refer to the Techstream operator manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the Techstream from the DLC3.



    A178528E02
  1. When not using the Techstream:

    1. Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C before connecting the probe.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer from the DLC3.



10. INSPECT COMPRESSION
  1. Remove the 8 spark plugs (Click here).



    A194643E01
  1. Check the cylinder compression pressure.

    NOTICE:
    Check each cylinder compression pressure in the same way.


    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Standard compression pressure:
      1300 kPa (13.3 kgf/cm2, 189 psi)

      Minimum pressure:
      1000 kPa (10.2 kgf/cm2, 145 psi) or more

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi) or less

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. This measurement must be done as quickly as possible.

    4. If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.

      HINT:
      1. If adding oil helps boost the compression, it is likely that the piston rings and/or cylinder bore are worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.



11. INSPECT CO/HC

HINT:
This check is used only to determine whether or not the idle CO/ HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.



    A185322
  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the A/F sensor and heated oxygen sensor operation.

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter