Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Manual Up / Down Function Via Back Door Lock Key Cylinder does not Operate

for Preparation Click here


DESCRIPTION

If the manual UP/DOWN function via the back door lock key cylinder does not operate, the back door lock key cylinder, the harness and connector, the back door ECU may be abnormal.

WIRING DIAGRAM


B191469E01


INSPECTION PROCEDURE

1.CHECK BACK DOOR WINDOW OPERATION
  1. Check that the back door power window operates via the back door power window switch.

    OK:
    Manual UP/DOWN function operates normally.



NG
GO TO OTHER FLOW CHART (BACK DOOR POWER WINDOW CIRCUIT) (Click here)
OK


2.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door P/W / Data List.

  1. According to the display on the Techstream, read the Data List.

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Switch Operation Locked
    Back door key lock and unlock switch signal / ON or OFF
    ON: Back door lock key cylinder is turned to unlock
    OFF: Key is in back door lock key cylinder (original position)
    -
    Key Switch Operation Unlocked
    Back door key lock and unlock switch signal / ON or OFF
    ON: Back door lock key cylinder is turned to unlock
    OFF: Key is in back door lock key cylinder (original position)
    -

OK:
The Techstream display changes normally when tail gate control switch is operated.



NG
Go to step 3
OK

REPLACE BACK DOOR ECU  

3.INSPECT TAIL GATE CONTROL SWITCH


    B191471E01
  1. Remove the tail gate control switch .

  1. Insert the key into the key cylinder.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 3 (E)
    Turn key to unlock position
    Below 1 Ω
    Turn key to lock position
    10 kΩ or higher
    2 (L) - 3 (E)
    Turn key to unlock position
    10 kΩ or higher
    Turn key to lock position
    Below 1 Ω

  1. Reinstall the tail gate control switch.



NG
REPLACE TAIL GATE CONTROL SWITCH
OK


4.INSPECT HARNESS AND CONNECTOR (BACK DOOR ECU - TAIL GATE CONTROL SWITCH)


    B191470E02
  1. Disconnect the V3 back door ECU connector.

  1. Disconnect the V18 tail gate control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V3-7 (BKUL) - V18-1 (UL)
    Always
    Below 1 Ω
    V3-8 (BKL) - V18-2 (L)
    Always
    Below 1 Ω
    V3-19 (KEYE) - V18-3 (E)
    Always
    Below 1 Ω
    V18-1 (UL) - Body ground
    Always
    10 kΩ or higher
    V18-2 (L) - Body ground
    Always
    10 kΩ or higher
    V18-3 (E) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the tail gate control switch connector.

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU