Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 3UR-FE, 3UR-FBE)

VANE PUMP (for 3UR-FE, 3UR-FBE) > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY


A163333E01

HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.



    C161012
  1. Install the vane pump with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



2. CONNECT PRESSURE FEED TUBE


C161011E01
  1. Install a new gasket to the pressure feed tube.

  1. Install the pressure feed tube with the union bolt.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



3. CONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR


C161010
  1. Connect power steering oil pressure sensor connector.



4. CONNECT NO.1 OIL RESERVOIR TO PUMP HOSE


    C161009E01
  1. Connect the pump hose with the clip.



5. CONNECT WIRE HARNESS CLAMP


C161008
  1. Connect the wire harness clamp.



6. INSTALL FAN AND GENERATOR V BELT


    A163771E01
  1. Set the fan and generator V belt onto every part.

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly set to each pulley.



    A174124E01
  1. After installing the belt, check that it fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



7. INSTALL AIR CLEANER ASSEMBLY


    A183246E01
  1. Attach grommet to air cleaner before mounting the air cleaner.

  1. Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.



    A183242
  1. Install the air cleaner with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector and install the clamp and wire harness.

  1. Connect the air cleaner hose and tighten the clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



8. INSTALL V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



9. ADD POWER STEERING FLUID


10. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)

    2. Repeat (*1) several times.

  1. Stop the engine.



    C124274E04
  1. Check for foaming or emulsification.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



11. INSPECT FOR POWER STEERING FLUID LEAK


12. INSTALL NO. 1 ENGINE UNDER COVER


A165576E03
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected .