EXHAUST PIPE > INSTALLATION |
| 1. INSTALL MONOLITHIC CONVERTER PROTECTOR (for Bank 1) |
![]() |
Install the 2 LH converter protector stays and 2 No. 2 converter protector stays.
Install the 2 monolithic converter protectors with the 4 bolts and 4 nuts.
| 2. INSTALL NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1) |
![]() |
Install the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.
Install the 2 No. 1 monolithic converter protectors with the 4 bolts and 4 nuts.
| 3. INSTALL MONOLITHIC CONVERTER PROTECTOR (for Bank 2) |
![]() |
Install the 2 LH converter protector stays and 2 No. 2 converter protector stays.
Install the 2 monolithic converter protectors with 4 bolts and 4 nuts.
Install the 2 No. 1 monolithic converter protectors with the 4 bolts and 4 nuts.
| 4. INSTALL NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2) |
![]() |
Install the 2 No. 2 converter protector stays and 2 No. 3 converter protector stays.
Install the 2 No. 1 monolithic converter protectors with 4 bolts and 4 nuts.
| 5. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1) |
![]() |
Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.
![]() |
Using SST, tighten the air fuel ratio sensor.
| 6. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1) |
![]() |
Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.
![]() |
Using SST, tighten the air fuel ratio sensor.
| 7. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 3 new nuts.
Connect the air fuel ratio sensor connector.
| 8. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
![]() |
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.
Connect the air fuel ratio sensor connector.
![]() |
Connect the front No. 3 exhaust pipe to the exhaust pipe support.
Install a new gasket and the front No. 3 exhaust pipe sub-assembly to the No. 2 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.
| 9. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) |
![]() |
Install the heated oxygen sensor to the front exhaust pipe assembly by hand.
![]() |
Using SST, tighten the heated oxygen sensor.
Connect the heated oxygen sensor connector.
| 10. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) |
![]() |
Install the heated oxygen sensor to the front No. 2 exhaust pipe assembly by hand.
![]() |
Using SST, tighten the heated oxygen sensor.
Connect the heated oxygen sensor connector and 2 clamps.
| 11. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
![]() |
Connect the center exhaust pipe to the 3 exhaust pipe supports.
Install 2 new gaskets to the front exhaust pipe.
Install the center exhaust pipe with the 4 bolts.
| 12. INSTALL TAILPIPE ASSEMBLY |
Connect the tailpipe to the exhaust pipe support.
![]() |
Install a new gasket to the center exhaust pipe.
Connect the tailpipe to the center exhaust pipe.
Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.
| 13. INSPECT FOR EXHAUST GAS LEAK |