TRANSFER ASSEMBLY > REASSEMBLY |
| 1. INSTALL REAR TRANSFER OUTPUT SHAFT |
![]() |
Install a new needle roller bearing.
![]() |
Install the transfer drive sprocket sub-assembly.
![]() |
Using SST and press, press in a new bearing.
| 2. INSTALL FRONT DRIVE CLUTCH SLEEVE |
![]() |
Install the transfer clutch hub onto the front drive clutch sleeve.
![]() |
Install the 3 shifting keys and 2 shifting key snap rings
![]() |
Install the synchronizer ring set.
![]() |
Install the 2 transfer clutch hub bearings.
![]() |
Install the front drive clutch sleeve with synchromesh onto the output shaft.
| 3. INSTALL CENTER DIFFERENTIAL CASE |
![]() |
Install the synchromesh shifting key spring and No. 2 synchromesh shifting keys as shown in the illustration.
![]() |
Using a snap ring expander, install the snap ring.
![]() |
Install the center differential case to the output shaft.
Install the straight pin to the output shaft.
| 4. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER |
![]() |
Install a new seal ring to the output shaft spacer.
![]() |
Align the pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.
![]() |
Using a screwdriver and hammer, tap on the snap ring.
| 5. INSTALL TRANSFER INPUT SHAFT PLUG |
![]() |
Using SST and a hammer, tap in a new input shaft plug until its surface is 1.0 to 1.8 mm (0.0394 to 0.0709 in.) from the input shaft upper surface.
| 6. INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH |
![]() |
Using SST and a hammer, tap in a new bush until its surface is 5.5 to 5.9 mm (0.217 to 0.232 in.) from the input shaft upper surface.
| 7. INSTALL TRANSFER INPUT SHAFT BEARING |
![]() |
Install the low planetary gear bearing and low planetary gear to the input shaft.
![]() |
Install the low planetary gear bearing and a new input shaft bearing to the input shaft.
![]() |
Using SST and a press, press in a new bearing.
![]() |
Select a snap ring that allows for minimum axial play and install it to the shaft.
| Mark | Thickness |
| C | 2.13 to 2.18 mm (0.0839 to 0.0858 in.) |
| D | 2.18 to 2.23 mm (0.0858 to 0.0878 in.) |
| E | 2.23 to 2.28 mm (0.0878 to 0.0898 in.) |
| F | 2.28 to 2.33 mm (0.0898 to 0.0917 in.) |
| G | 2.33 to 2.38 mm (0.0918 to 0.0937 in.) |
| H | 2.38 to 2.43 mm (0.0937 to 0.0957 in.) |
| J | 2.43 to 2.48 mm (0.0957 to 0.0976 in.) |
Using a snap ring expander, install the snap ring.
| 8. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING |
![]() |
Apply transfer oil to a new seal ring.
Install a new seal ring to the input shaft.
| 9. INSTALL TRANSFER DRIVEN SPROCKET BEARING |
![]() |
Install a new bearing to the front case in the direction shown in the illustration.
![]() |
Using a screwdriver, install the snap ring.
| 10. INSTALL TRANSFER LOW PLANETARY RING GEAR |
![]() |
Install the snap ring to the front case.
![]() |
Install the ring gear to the transfer front case.
![]() |
Using a screwdriver install the snap ring.
| 11. INSTALL INPUT SHAFT ASSEMBLY |
![]() |
While expanding the snap ring, install the input shaft to the front case.
Apply adhesive to the threads of the 2 plugs.
![]() |
Using a 14 mm hexagon wrench, install the 2 plugs.
| 12. INSTALL TRANSFER CASE MAGNET |
![]() |
Install the transfer case magnet.
| 13. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY |
![]() |
Install a new O-ring.
![]() |
Install the oil separator with the 3 bolts.
| 14. INSTALL SIDE GEAR SHAFT HOLDER BEARING |
![]() |
Using SST and hammer, install a new side gear shaft holder bearing.
![]() |
Using a screwdriver, install the snap ring.
| 15. INSTALL REAR OUTPUT SHAFT |
Install the snap ring to the rear case.
Mount the rear case in a vise.
![]() |
Install the rear output shaft , front drive chain and driven sprocket.
![]() |
Using a snap ring expander, install the snap ring to the out put shaft.
| 16. INSTALL TRANSFER HIGH & LOW CLUTCH SLEEVE |
![]() |
Install the transfer high and low clutch sleeve to the output shaft.
| 17. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY |
![]() |
Install the washer to the rear case.
![]() |
Install a new O-ring to the shift actuator.
![]() |
Set the No. 1 gear shift fork and No. 2 gear shift fork to the rear case. Then install the shift actuator to the rear case with the 3 bolts.
![]() |
Install the 2 bolts.
![]() |
Using a screwdriver and hammer, tap the 3 shift fork shaft snap rings into the shift fork shaft.
| 18. INSTALL NO. 1 SYNCHRONIZER RING |
![]() |
Align the protrusion of the synchronizer ring with the notch on the differential case and install it.
| 19. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING |
![]() |
Install the output shaft spacer.
![]() |
Install the transfer output shaft front needle roller bearing.
| 20. INSTALL REAR TRANSFER CASE |
![]() |
Apply seal packing to the rear case as shown in the illustration.
![]() |
Install the rear case with the 14 bolts.
| 21. INSTALL TRANSFER CASE PLUG |
Apply adhesive to the threads of the plug.
![]() |
Using a 6 mm hexagon wrench, install the plug.
| 22. INSTALL NO. 1 TRANSFER CASE PLUG |
![]() |
Install the pin and compression spring to the front case.
Apply adhesive to the threads of the plug.
Install the plug.
| 23. INSTALL TRANSFER CASE FRONT OIL SEAL |
Apply transfer oil to the spline area of the output shaft.
![]() |
Using SST and a hammer, tap in the oil seal until its surface is 1 to 1.5 mm (0.0394 to 0.0591 in.) from the case upper surface.
| 24. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
Install the companion flange sub-assembly onto the drive sprocket sub-assembly.
![]() |
Using SST to hold the companion flange.
Using a socket wrench (32mm), install a new O-ring and a new companion flange lock nut.
![]() |
Using a chisel and hammer, stake the companion flange lock nut.
| 25. INSTALL TRANSFER CASE REAR OIL SEAL |
![]() |
Install the 2 output washers.
Apply transfer oil to the spline area of the output shaft.
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the housing upper surface.
| 26. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
Install the companion flange onto the output shaft.
![]() |
Using SST to hold the companion flange.
Using a socket wrench (32mm), install a new O-ring and a new companion flange lock nut.
![]() |
Using a chisel and hammer, stake the companion flange lock nut.
| 27. INSTALL TRANSFER OIL PUMP PLATE OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump plate upper surface.
| 28. INSTALL TRANSFER CASE STRAIGHT PIN |
![]() |
Install the 2 straight pins to the input shaft.
| 29. INSTALL TRANSFER OIL PUMP PLATE |
Apply transfer oil to a new O-ring, drive rotor and driven rotor.
![]() |
Install the O-ring.
![]() |
Install the drive rotors.
![]() |
Install a new seal ring to the input shaft.
![]() |
Install the oil pump plate with the 4 bolts.
| 30. INSTALL TRANSFER CASE PLUG |
![]() |
Install the relief valve seat, ball and compression spring to the oil pump plate.
Apply adhesive to the threads of the plug.
Using a 10 mm hexagon wrench, install the plug.
| 31. INSTALL HEAT INSULATOR BRACKET |
![]() |
Install the heat insulator bracket with the bolt.