WATER PUMP > INSTALLATION |
| 1. INSTALL ENGINE WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the engine water pump with the 8 bolts shown in the illustration.
| 2. INSTALL WATER PUMP PULLEY |
![]() |
Temporarily install the pulley with the 4 bolts.
Using SST, hold the pulley and tighten the 4 bolts.
| 3. INSTALL INLET WATER HOUSING |
![]() |
Install a new gasket to the water pump.
![]() |
Connect the No. 3 water by-pass hose to the inlet water housing.
Install the inlet water housing with the 3 bolts.
| 4. CONNECT NO. 5 WATER BY-PASS HOSE |
![]() |
Connect the No. 5 water by-pass hose.
| 5. INSTALL AIR PIPE SUB-ASSEMBLY |
![]() |
Install the air pipe with the bolt.
Connect the connector and install the wire harness with the 2 clamps.
| 6. CONNECT NO. 2 AIR INJECTION SYSTEM HOSE |
![]() |
Connect the No. 2 air injection hose.
Attach the wire harness clamp.
Connect the air pump connector.
| 7. CONNECT NO. 3 AIR INJECTION SYSTEM HOSE |
![]() |
Connect the No. 3 air injection hose.
| 8. CONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System) |
![]() |
Connect the 4 hoses.
Install the water by-pass hose with the 3 bolts.
| 9. INSTALL NO. 1 WATER BY-PASS HOSE |
![]() |
Connect the No. 1 water by-pass hose to the water by-pass joint and water inlet housing.
| 10. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
![]() |
for Condenser with Separate Oil Cooler:
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 11. INSTALL INLET RADIATOR HOSE |
![]() |
Install the inlet radiator hose.
| 12. CONNECT OUTLET RADIATOR HOSE |
![]() |
Connect the outlet radiator hose to the water inlet housing.
| 13. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Connect the air cleaner hose and tighten clamp.
Connect the No. 2 ventilation hose with the clamp.
Connect the vacuum hose.
| 14. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Attach grommet to air cleaner before mounting the air cleaner.
Insert the air cleaner into the fender apron hole, and fully insert pin to grommet.
![]() |
Install the air cleaner with the 2 bolts.
Connect the connector and install the clamp and wire harness.
Connect the air cleaner hose and tighten the clamp.
| 15. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 14.6 liters (15.4 US qts., 12.8 Imp. qts.) |
| w/o Trailer Towing System | 13.7 liters (14.5 US qts., 12.0 Imp. qts.) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 16. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 17. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 18. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.