Home › Engine / Hybrid System ยท 3UR-FBE › COOLING › WATER PUMP

WATER PUMP > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A191562E01

  1. Tighten the radiator drain cock plug by hand.



3. REMOVE V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



4. REMOVE AIR CLEANER ASSEMBLY


    A183242
  1. Loosen the hose clamp and disconnect the air cleaner from the air cleaner hose.

  1. Loosen the 2 bolts and remove the air cleaner with the grommet.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A183244
  1. Disconnect the No. 2 ventilation hose.

  1. Disconnect the vacuum hose.

  1. Loosen the hose clamp and remove the air cleaner hose.



6. REMOVE INLET RADIATOR HOSE


    A183232
  1. Remove the inlet radiator hose.



7. DISCONNECT OUTLET RADIATOR HOSE


    A183247
  1. Disconnect the outlet radiator hose from the water inlet housing.



8. REMOVE FAN SHROUD


    A151842
  1. Loosen the 4 nuts holding the fluid coupling and fan.

  1. Remove the fan and generator V belt .



    A161784
  1. for Condenser with Separate Oil Cooler:
    Detach the claw to open the No. 1 flexible hose clamp.



    A183235
  1. Disconnect the reservoir hose from the upper radiator tank.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



9. DISCONNECT WATER BY-PASS PIPE HOSE (w/ Trailer Towing System)
  1. Remove the 3 bolts.



    A165547
  1. Disconnect the 4 hoses and remove the water by-pass pipe.



10. DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE


    A183217
  1. Disconnect the No. 3 air injection hose.



11. DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE


    A183219
  1. Disconnect the connector and separate the wire harness clamp.

  1. Disconnect the No. 2 air injection hose.



12. SEPARATE AIR PIPE SUB-ASSEMBLY


    A183221
  1. Disconnect the connector and separate the 2 clamps and wire harness.

  1. Remove bolt and separate the air pipe.



13. DISCONNECT NO. 5 WATER BY-PASS HOSE


    A183224
  1. Disconnect the No. 5 water by-pass hose.



14. REMOVE NO. 1 WATER BY-PASS HOSE


    A158577E03
  1. Disconnect the No. 1 water by-pass hose from the water by-pass joint and water inlet housing.



15. REMOVE WATER INLET HOUSING


    A183226
  1. Remove the 3 bolts and water inlet housing and disconnect the No. 3 water by-pass hose from the water inlet housing.

  1. Remove the gasket from the water pump.



16. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



17. REMOVE ENGINE WATER PUMP ASSEMBLY


    A151828
  1. Remove the 8 bolts, engine water pump and the gasket.