CAMSHAFT > INSTALLATION |
| 1. INSTALL CAMSHAFTS (for Bank 1) |
![]() |
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 3 and No. 4 camshafts to the camshaft housing.
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.
![]() |
Temporarily install the 10 bolts in the order shown in the illustration.
| 2. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Make sure that the valve rocker arms are installed as shown in the illustration.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.
![]() |
Tighten the 10 bolts in the order shown in the illustration.
| 3. INSTALL CAMSHAFTS (for Bank 2) |
![]() |
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 1 and No. 2 camshafts to the camshaft housing.
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.
![]() |
Temporarily install the 10 bolts in the order shown in the illustration.
| 4. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Make sure that the valve rocker arms are installed as shown in the illustration.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.
![]() |
Tighten the 10 bolts in the order shown in the illustration.
| 5. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the chain tensioner with the 2 bolts.
While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
| 6. INSTALL CHAIN SUB-ASSEMBLY (for RH Side) |
![]() |
Align the No. 1 chain's orange mark plate with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
![]() |
Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
![]() |
Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.
Install the crankshaft timing sprocket to the crankshaft.
Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.
Remove the pin from the No. 2 chain tensioner.
Using a wrench to hold the hexagonal portion of the No. 1 camshaft, temporarily install the bolt.
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, temporarily install the bolt.
| 7. INSTALL NO. 1 CHAIN VIBRATION DAMPER (for RH Side) |
![]() |
Install the vibration damper with the 2 bolts.
| 8. INSTALL CHAIN TENSIONER SLIPPER (for RH Side) |
![]() |
| 9. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY (for RH Side) |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
![]() |
Install the chain tensioner with the 2 bolts.
Remove the hexagon wrench from the chain tensioner.
| 10. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the chain tensioner with the 2 bolts.
While pushing down the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
| 11. INSTALL CHAIN SUB-ASSEMBLY (for LH Side) |
![]() |
Align the No. 1 chain's orange mark plate with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
![]() |
Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.
![]() |
Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.
Install the crankshaft timing sprocket to the crankshaft.
Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear.
Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear.
Remove the pin from the No. 3 chain tensioner.
Using a wrench to hold the hexagonal portion of the No. 3 camshaft, temporarily install the bolt.
Using a wrench to hold the hexagonal portion of the No. 4 camshaft, temporarily install the bolt.
| 12. INSTALL CHAIN TENSIONER SLIPPER (for LH Side) |
![]() |
| 13. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY (for LH Side) |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
![]() |
Install a new gasket and the chain tensioner with the 2 bolts.
| 14. INSTALL NO. 1 CHAIN VIBRATION DAMPER (for LH Side) |
![]() |
Install the vibration damper with the 2 bolts.
Remove the hexagon wrench from the No. 1 chain tensioner.
| 15. TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY (for LH Side) |
![]() |
Using a wrench to hold the hexagonal portion of the No. 3 camshaft, tighten the camshaft timing gear with the bolt.
![]() |
Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the camshaft timing exhaust gear with the bolt.
| 16. TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY (for RH Side) |
![]() |
Using a wrench to hold the hexagonal portion of the No. 1 camshaft, tighten the camshaft timing gear with the bolt.
![]() |
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the camshaft timing exhaust gear with the bolt.
| 17. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the pulley set bolt.
Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

Remove the crankshaft pulley bolt.
| 18. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
Install the timing chain cover (Click here).