DTC P050B Cold Start Ignition Timing Performance |

| DTC Code | DTC Detection Condition | Trouble Area |
| P050B | Insufficient ignition timing retard at cold start (2-trip detection logic) |
|
| Related DTCs | P050B: Cold start ignition timing performance |
| Required Sensors/Components (Main) | Throttle body assembly |
| Required Sensors/Components (Related) | Mass air flow meter Engine Coolant Temperature (ECT) sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil control valve) P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0013, P0023 (Exhaust VVT Oil control valve) P0014, P0024 (Exhaust VVT System - Advance) P0015, P0025 (Exhaust VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P1340 (Camshaft position sensor) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| ECT at engine start | -10°C (14°F) or more |
| ECT | -10 to 50°C (14 to 122°F) |
| Engine idling time | 3 seconds or more |
| Fuel-cut | OFF |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Accumulated time when ignition timing retard value is cut off | 5 seconds or more |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Symptoms | Factor | Trouble Area |
| Low idle speed when engine is cold (immediately after engine start) | Excessive engine friction |
|
| Rough idle when engine is cold (immediately after engine start) | Abnormal combustion | Fuel quality |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P050B | A |
| P050B and other DTCs | B |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the Techstream.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.
|
| ||||
| OK | |
| 3.INSPECT THROTTLE BODY |
Check that there are no deposits around the throttle valve.
|
| ||||
| OK | |
| Go to step 14 |
| 4.REPAIR OR REPLACE THROTTLE BODY |
Repair or replace the throttle body (Click here).
|
| ||||
| 5.CHECK PCV SYSTEM |
Start the engine.
Pinch the positive crankcase ventilation hose.
Check the engine rpm.
|
| ||||
| OK | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks .
|
| ||||
| OK | |
| 7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Turn the A/C on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.
| Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
| OK | |
| Go to step 14 |
| 10.REPAIR OR REPLACE PCV SYSTEM |
Repair or replace the PCV system.
|
| ||||
| 11.REPAIR OR REPLACE AIR INDUCTION SYSTEM |
Repair or replace the air induction system.
|
| ||||
| 12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Replace the air cleaner filter element sub-assembly.
|
| ||||
| 13.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050B is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the D3 MAF meter connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D3-3 (VG) - D56-74 (VG) | Always | Below 1 Ω |
| D3-2 (E2G) - D56-75 (E2G) | Always | Below 1 Ω |
| D3-3 (VG) or D56-74 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||