Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Front Fog Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a front fog light switch information signal from the light control switch (front fog switch), and illuminates the front fog lights.

WIRING DIAGRAM


E176436E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT FOG LIGHT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test / Front Fog Light.

  1. Check that the front fog lights turn on/off.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Fog Light Relay
    Front fog light
    ON or OFF
    -

    OK:
    Front fog lights turn on/off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (FOG)


    E161570E03
  1. Remove the FOG fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    FOG fuse
    Always
    Below 1 Ω

  1. Reinstall the FOG fuse.



NG
REPLACE FUSE
OK


3.INSPECT FOG LIGHT BULB
  1. Temporarily replace the front fog light bulb with a new or normally functioning one .

  1. Check that the front fog light turn on.

    OK:
    front fog light turn on.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY)
E146024E07
  1. for LH:

    1. Disconnect the A36 front fog light LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A36-2 - Body ground
      Light control switch TAIL, front fog light switch ON
      11 to 14 V
      Light control switch TAIL, front fog light switch OFF
      Below 1 V

    3. Reconnect the front fog light LH connector.

  1. for RH:

    1. Disconnect the A37 front fog light RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A37-2 - Body ground
      Light control switch TAIL, front fog light switch ON
      11 to 14 V
      Light control switch TAIL, front fog light switch OFF
      Below 1 V

    3. Reconnect the front fog light RH connector.



NG
Go to step 5
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT FOG LIGHT BULB - BODY GROUND) 

5.INSPECT FOG LIGHT RELAY (FOG)
E121182E12
  1. Remove the FOG relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FOG relay.



NG
REPLACE FOG RELAY
OK


6.CHECK HARNESS AND CONNECTOR (FOG RELAY - BATTERY, TAIL RELAY)
E147140E05
  1. Remove the FOG relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    FOG relay terminal 1 - Body ground
    Light control switch TAIL
    11 to 14 V
    FOG relay terminal 3 - Body ground
    Always
    11 to 14 V

  1. Reinstall the FOG relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (FOG RELAY - FRONT FOG LIGHT BULB)


    E161594E02
  1. Remove the FOG relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A36 front fog light LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      FOG relay terminal 5 - A36-2
      Always
      Below 1 Ω
      FOG relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reconnect the front fog light LH connector.

  1. for RH:

    1. Disconnect the A37 front fog light RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      FOG relay terminal 5 - A37-2
      Always
      Below 1 Ω
      FOG relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reconnect the front fog light RH connector.

  1. Reinstall the FOG relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (FOG RELAY - MAIN BODY ECU)
E147119E05
  1. Disconnect the H4 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H4-4 - Body ground
    Light control switch TAIL
    11 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU