ENGINE IMMOBILISER SYSTEM > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
When adding master keys or sub-keys (additional registration).
Register key code in the transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "A" |
After replacing the transponder key ECU (New key code registration).
Register the key code (immobiliser code) in the new transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "B" |
Register the ECU - ECM COMMUNICATION ID between the ECM and the new transponder key ECU.
| Target ECU | See Procedure |
| ECM | Procedure "C" |
After replacing the ECM.
Reregister the ECU - ECM COMMUNICATION ID between the new ECM and the transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "C" |
After replacing the transponder key ECU and ECM.
Register the ECU - ECM COMMUNICATION ID between the new ECM and the new transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "C" |
Erasure of key codes.
Erase all of the key codes except master key.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "D" |
Erase all of the key codes.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "D" |
| 2. NEW KEY REGISTRATION (PROCEDURE "B") |
New key code registration
When using Techstream
| Procedure | Security Indicator Light Condition |
| 1. Start registration. | Security indicator light is blinking. |
| 2. Insert one of master keys into the ignition key cylinder. | Security indicator light turned on. |
| 3. Select following items on the Techstream: (1) Body Electrical (2) Immobiliser (3) Utility (4) Key Registration
| Security indicator light turned off for 1 sec. and then turned on. |
| 4. Remove the key. | Security indicator light turned on.
|
| 5. Register another key? YES: Go to step 6. NO: Go to step 7.
| |
| 6. Insert another key into the ignition key cylinder. Then go to step 4. | Security indicator light turned off for 1 sec. and then turned on. |
| 7. End of registration. | |
End the new key code registration mode (when not using Techstream)
Turn the ignition switch to ON and off 5 times within 10 seconds using a master key that has already been registered.
End the new key code registration mode (when using Techstream)
Insert the key into the ignition key cylinder and turn the Techstream ON.
Follow the instructions on the Techstream screen to end the new key code registration mode.

| 3. REGISTRATION OF ADDITIONAL KEY (PROCEDURE "A") |
Additional key code registration
When using Techstream
| Procedure | Security Indicator Light Condition | Time (Completion of Operation) |
| 1. Start registration. | Security indicator light is blinking. | - |
| 2. Insert an already registered master key into the ignition key cylinder, turn the ignition switch to ON, and turn the Techstream ON. | Security indicator light turned off. | Within 120 sec. |
| 3. Select following items on the Techstream: (1) Body Electrical (2) Immobiliser (3) Utility (4) Key Registration | Security indicator light turned on. | |
| 4. Remove the master key and then push NEXT button on the Techstream. | Security indicator light turned on. | Within 20 sec. of the instruction on the Techstream. |
| 5. Insert unregistered key into the ignition key cylinder. | Security indicator light is blinking.
| Within 10 sec. |
6. After 60 sec., key is registered.
| Security indicator light turned off. | - |
| 7. Remove the key. | Security indicator light is blinking. | |
| 8. Techstream screen displays number of registered keys. | ||
| 9. Register another key? YES: Go to step 2. NO: Go to step 10. | ||
| 10. End of registration. | ||
| 4. ERASURE OF KEY CODE (PROCEDURE "D") |
Erasure all key codes except master key
When using Techstream
| Procedure | Security Indicator Light Condition | Time (Completion of Operation) |
| 1. Start of erasure. | Security indicator light is blinking. | - |
| 2. Insert previously registered master key into ignition key cylinder and turn ignition switch to ON. | Security indicator light turned off. | Within 120 sec. |
| 3. Select following items on the Techstream: (1) Body Electrical (2) Immobiliser (3) Utility (4) Transponder Code Erasure | Security indicator light turned on for 1 sec. then turned off. | |
4. Remove the master key.
| Security indicator light turned on. | Within 10 sec. of the instruction on the Techstream. |
| 5. End of erasure. | ||
Erasure all of key codes
When using Techstream
| Procedure | Security Indicator Light Condition | Time (Completion of Operation) |
| 1. Using TIS, confirm that user and vehicle match. | Security indicator light is blinking. | - |
| 2. Start of erasure. | Security indicator light is blinking. | - |
| 3. Insert previously registered master key or unregistered key into ignition key cylinder and turn ignition switch to ON. | Security indicator light turned off. | Within 120 sec. |
| 4. Select following items on the Techstream: (1) Body Electrical (2) Immobiliser (3) Utility (4) Immobiliser Code Reset | Security indicator light turned on for 1 sec. then turned off. | Within 15 min. |
| 5. Completion of erasure of all key codes is displayed. | Security indicator light turned on. | - |
| 6. End of erasure. | ||
| 5. ECU - ECM COMMUNICATION ID REGISTRATION (PROCEDURE "C") |
After replacing the transponder key ECU

Register the key code(s) by following the new key code registration procedure (procedure "B").
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 before inserting the key into the key cylinder.
| Procedure | Security Indicator Light Condition |
1. Insert previously registered key into ignition key cylinder and turn ignition switch to ON.
| Security indicator light turned off. |
| 2. Leave vehicle as is for 30 min. | |
| 3. Turn the ignition switch off and disconnect terminals TC and CG. | |
| 4. Start engine. | |
| 5. Check that engine starts and stays on for more than 3 sec. Registration is complete. |
After replacing the ECM
Register the ECU - ECM communication ID.
| Procedure | Security Indicator Light Condition |
| 1. Insert previously registered key into ignition key cylinder. | Security indicator light turned off. |
| 2. Start engine. | |
| 3. Check that engine starts and stays on for more than 3 sec. Registration is complete. |
After replacing the transponder key ECU and ECM
Register the key code(s) by following the new key code registration procedure (procedure "B").
Register the ECU - ECM communication ID.
| Procedure | Security Indicator Light Condition |
| 1. Insert previously registered key into ignition key cylinder. | Security indicator light turned off. |
| 2. Start engine. | |
| 3. Check that engine starts and stays on for more than 3 sec. Registration is complete. |