ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Disconnect the H27 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H27-7 (AGND) - Body ground | GR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H27 amplifier connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H27-1 (VC5) - H27-7 (AGND) | G - GR | Power supply | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | 4.6 to 5.4 V | |||
| H27-4 (CODE) - H27-7 (AGND) | LG - GR | Demodulated signal of key code data | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | Pulse generation (see waveform 1) | |||
| H27-5 (TXCT) - H27-7 (AGND) | L - GR | Key code output signal | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | Pulse generation (see waveform 2) | |||
| H27-7 (AGND) - Body ground | GR - Body ground | Ground | Always | Below 1 Ω |
![]() |
Using an oscilloscope, check the waveform 1.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H27-4 (CODE) - H27-7 (AGND) | 5 V/DIV., 20 msec./DIV. | Key inserted in ignition key cylinder |
![]() |
Using an oscilloscope, check the waveform 2.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H27-5 (TXCT) - H27-7 (AGND) | 5 V/DIV., 20 msec./DIV. | Key inserted in ignition key cylinder |
| CHECK TRANSPONDER KEY ECU |

Disconnect the H32 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H32-16 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| H32-1 (+B) - H32-16 (GND) | G - W-B | Battery | Always | 11 to 14 V |
| H32-2 (IG) - H32-16 (GND) | GR - W-B | Ignition switch | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| H32-3 (KSW) - H32-16 (GND) | LG - W-B | Unlock warning switch | No key in ignition key cylinder | 10 kΩ or higher |
| Key inserted in ignition key cylinder | Below 1 Ω |
Reconnect the H32 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H32-14 (VC5) - H32-16 (GND) | G - W-B | Power source | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | 4.6 to 5.4 V | |||
| H32-7 (CTY) - H32-16 (GND) | Y - W-B | Door courtesy | Door closed | 10 kΩ or higher |
| Door open | Below 1 Ω | |||
| H32-4 (TXCT) - H32-16 (GND) | L - W-B | Transponder key amplifier communication signal | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | Pulse generation (see waveform 1) | |||
| H32-15 (CODE) - H32-16 (GND) | LG - W-B | Transponder key amplifier communication signal | No key in ignition key cylinder | Below 1 V |
| Key inserted in ignition key cylinder | Pulse generation (see waveform 2) | |||
| H32-13 (EFIO) - H32-16 (GND) | Y - W-B | ECM output signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (see waveform 3) | |||
| H32-12 (EFII) - H32-16 (GND) | SB - W-B | ECM input signal | Always | Pulse generation (see waveform 4) |
| H32-8 (IND) - H32-16 (GND) | V - W-B | Security indicator light signal | Immobiliser set status | Alternating between 11 to 14 V and below 1 V |
| Immobiliser unset status | Below 1 V | |||
| H32-9 (D) - H32-16 (GND) | B - W-B | Diagnosis tester communication | Always | Pulse generation |
![]() |
Using an oscilloscope, check the waveform 1.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H32-4 (TXCT) - H32-16 (GND) | 5 V/DIV., 20 msec./DIV. | Key inserted in ignition key cylinder |
![]() |
Using an oscilloscope, check the waveform 2.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H32-15 (CODE) - H32-16 (GND) | 5 V/DIV., 20 msec./DIV. | Key inserted in ignition key cylinder |
![]() |
Using an oscilloscope, check the waveform 3.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H32-13 (EFIO) - H32-16 (GND) | 10 V/DIV., 100 msec./DIV. | Ignition switch ON |
![]() |
Using an oscilloscope, check the waveform 4.
| Terminal No. (Symbol) | Tool Setting | Condition |
| H32-12 (EFII) - H32-16 (GND) | 10 V/DIV., 100 msec./DIV. | Always |