FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY |
| 1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side) |
![]() |
Engage the wire harness clamp.
Connect the 4 connectors and install the front seat wire.
| 2. INSTALL FRONT SEAT WIRE LH (for Driver Side) |
| 3. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side) |
![]() |
Engage the 3 claws and install the bush.
![]() |
Install the lumbar support adjuster assembly with the 2 screws.
Connect the lumbar support adjuster connector.
![]() |
Engage the 6 hooks to install the seatback springs.
Install the 2 springs.
| 4. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH |
![]() |
Engage the claw and install the front seat cushion shield lower.
| 5. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH |
| 6. INSTALL FRONT SEATBACK SHIELD LH |
![]() |
Engage the claw and install the front seatback shield.
Install the screw.
| 7. INSTALL FRONT SEATBACK SHIELD RH (for Driver Side) |
![]() |
Engage the claw and install the front seatback shield.
Install the screw.
Engage the wire harness clamp.
| 8. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Install the reclining adjuster inside cover with the screw.
| 9. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
| 10. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.
![]() |
Connect the seatback cover bracket to the seatback pad.
![]() |
Install the seatback cover wires.
Using hog ring pliers, install 2 new hog rings to the seatback pad.
| 11. INSTALL SEATBACK COVER WITH PAD |
![]() |
Install the seatback cover with pad to the seatback frame.
Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.
Lift the seatback cover, connect the seatback cover bracket to the seat frame, and install the nut.
| 12. INSTALL FRONT SEAT HEADREST SUPPORT |
![]() |
Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.
Engage the 4 claws to install the 2 headrest supports.
![]() |
Install the seatback cover wires.
Using hog ring pliers, install 2 new hog rings to the seat frame.
![]() |
Engage the hook.
![]() |
Using hog ring pliers, install 3 new hog rings to the seat frame.
| 13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.
| 14. INSTALL SEAT CUSHION COVER WITH PAD (for Driver Side) |
![]() |
Engage the hooks to install the seat cushion cover with pad.
Bend the 2 seat frame claws downward.
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion spring with 2 new hog rings.
![]() |
Engage the wire harness clamp.
![]() |
Engage the 8 wire harness clamps.
![]() |
Install the 2 clips.
| 15. INSTALL SEAT CUSHION COVER WITH PAD (for Front Passenger Side) |
![]() |
Engage the hooks to install the seat cushion cover with pad.
Bend the 2 seat frame claws downward.
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion spring with 2 new hog rings.
![]() |
Engage the 3 wire harness clamps.
![]() |
Install the 2 clips.
| 16. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the front seat inner belt LH with the nut.
![]() |
Connect the connector and engage the 5 clamps.
| 17. INSTALL SEAT POSITION AIRBAG SENSOR |
Check that the ignition switch is turned off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.
![]() |
Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.
Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).
Connect the connector to the seat position airbag sensor.
Check that there is no looseness in the installation parts of the seat position airbag sensor.
Engage the pin and install a new seat position sensor protector.
| 18. INSTALL FRONT SEAT CUSHION SHIELD INNER LH |
![]() |
Install the harness to the front seat cushion shield.
Engage the 3 claws in the order shown in the illustration, and install the cushion shield.
Install the screw.
| 19. INSTALL FRONT POWER SEAT LUMBAR SWITCH (for Driver Side) |
![]() |
Install the front power seat lumbar switch with the 2 screws.
Connect the connector.
| 20. INSTALL FRONT SEAT CUSHION SHIELD LH (for Driver Side) |
![]() |
Connect the connector and install the harness to the front seat cushion shield.
Engage the 3 claws in the order shown in the illustration, and install the front seat cushion shield.
Install the 3 screws.
![]() |
Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.
| 21. INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side) |
![]() |
Engage the 3 claws in the order shown in the illustration, and install the cushion shield.
Install the 2 screws.
![]() |
Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.
| 22. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Engage the claw to install the reclining adjuster release handle.
| 23. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side) |
![]() |
Engage the claw to install the reclining adjuster release handle.
| 24. INSTALL VERTICAL SEAT ADJUSTER KNOB (for Driver Side) |
![]() |
Install the snap ring to the vertical seat adjuster knob.
Install the vertical seat adjuster knob to the front seat.
| 25. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side) |
![]() |
Install the vertical adjusting handle with the 2 screws.
| 26. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side) |
![]() |
Engage the 2 claws to install the vertical adjuster handle cap.
| 27. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Check that the ignition switch is off.
Check that the negative battery (-) terminal is disconnected.
Engage the claw and occupant classification ECU.
Connect the connector to the occupant classification ECU.