FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY |
| 1. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Driver Side) |
![]() |
Install the front power seat motor assembly (slide motor) to the slide screws.
Clean the slide screws with non-residue solvent and apply adhesive to their threads.
Using a 4 mm socket hexagon wrench, install the new 2 bolts.
Using a 4 mm socket hexagon wrench, install the 2 bolts.
![]() |
Install the new 2 nuts.
![]() |
Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat and align the matchmarks.
![]() |
Check that the matchmarks are aligned on both sides.
If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.
| 2. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Front Passenger Side) |
![]() |
Install the front power seat motor assembly (slide motor) to the slide screws.
Clean the slide screws with non-residue solvent and apply adhesive to their threads.
Using a 4 mm socket hexagon wrench, install the new 2 bolts.
Using a 4 mm socket hexagon wrench, install the 2 bolts.
![]() |
Install the new 2 nuts.
![]() |
Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1, and then slide the seat and align the matchmarks.
![]() |
Check that the matchmarks are aligned on both sides.
If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.
| 3. INSTALL FRONT SEAT WIRE LH (for Driver Side) |
![]() |
Connect the 3 connectors and attach the 6 wire harness clamps.
| 4. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side) |
![]() |
Connect the 5 connectors and attach the 7 wire harness clamps.
| 5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Attach the claw to install the seat heater control.
Attach the wire harness clamp and connect the connector.
| 6. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System) |
![]() |
Attach the 2 claws and install the seat cushion climate control blower by pushing it forward.
Bend the bracket closed.
Using a T30 "TORX" socket, install the "TORX" screw.
Connect the connector.
| 7. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System) |
![]() |
Attach the 2 claws to install the seat cushion climate control duct.
Attach the 2 clamps (B).
Attach the 2 clamps (A).
| 8. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System) |
![]() |
Attach the 6 clamps and install the seatback climate control cover LH No. 2.
| 9. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
![]() |
Install the seatback climate control cover LH No. 3.
Using a T30 "TORX" socket, install the seatback climate control blower with the 2 "TORX" screws.
Attach the connector.
| 10. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System) |
![]() |
Using a T30 "TORX" socket, install the seatback climate control cover LH No. 1 with the 4 "TORX" screws.
| 11. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System) |
![]() |
Attach the 3 claws to install the bush.
![]() |
Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
![]() |
Attach the 4 hooks to install the seatback spring.
Install the 4 springs.
![]() |
Attach the 2 wire harness clamps and connect the connector.
| 12. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System) |
![]() |
Attach the 3 claws to install the bush.
![]() |
Install the lumbar support adjuster with the 2 screws.
Connect the lumbar support adjuster connector.
![]() |
Attach the 6 hooks to install the seatback spring.
| 13. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2 |
![]() |
Attach the hook to install the cushion shield.
Install the screw.
| 14. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1 |
| 15. INSTALL FRONT SEATBACK SHIELD LH |
![]() |
Attach the claw to install the seatback shield.
Install the 2 screws.
| 16. INSTALL FRONT SEATBACK SHIELD RH |
![]() |
Attach the claw to install the seatback shield.
Install the 2 screws.
Attach the wire harness clamp.
| 17. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Attach the claw to install the reclining adjuster inside cover.
Install the screw.
| 18. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
| 19. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Set the seatback heater with the name stamp side facing the seatback cover.
Install the seatback heater with new 9 tack pins.
| 20. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.
![]() |
Connect the seatback cover bracket to the seatback pad.
![]() |
Install the seatback cover wires.
Using hog ring pliers, install 2 new hog rings to the seatback pad.
| 21. INSTALL SEATBACK COVER WITH PAD |
![]() |
Install the seatback cover with pad to the seatback frame.
Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.
Lift the seatback cover, attach the seatback cover bracket to the seat frame, and install the nut.
![]() |
Install the seatback cover wires.
Using hog ring pliers, install 2 new hog rings to the seat frame.
![]() |
Attach the 3 hooks.
![]() |
Using hog ring pliers, install 3 new hog rings to the seat frame.
| 22. INSTALL FRONT SEAT HEADREST SUPPORT |
![]() |
Align the protruding portion of the front seat headrest supports with the installation grooves of the front seatback frame.
Attach the 4 claws to install the 2 headrest supports.
| 23. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Set the seat cushion heater with the name stamp side facing the seat cushion cover.
Install the seat cushion heater with new 30 tack pins.
| 24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch) |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.

| 25. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch) |
![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.
| 26. INSTALL SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch) |
![]() |
Install the seat cushion cover with pad to the seat frame.
Install the seat cushion cover wire.
![]() |
Using hog ring pliers, install 4 new hog rings and attach the hooks.
![]() |
Connect the connector and attach the 2 wire harness clamps.
![]() |
Connect the connector and attach the 2 wire harness clamps.
![]() |
Install the 2 clips.
| 27. INSTALL SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch) |
![]() |
Attach the hooks to install the seat cushion cover with pad.
Using hog ring pliers, install 2 new hog rings.
Bend the 2 seat frame claws downward.
![]() |
Connect the connector and attach the 2 wire harness clamps.
![]() |
Connect the connector and attach the 2 wire harness clamps.
![]() |
Install the 2 clips.
| 28. INSTALL FRONT POWER SEAT SWITCH LH |
![]() |
Install the switch with the 3 screws.
Connect the connectors.
| 29. INSTALL FRONT SEAT CUSHION SHIELD INNER LH |
![]() |
Attach the 2 claws and clip to install the cushion shield.
Install the screw.
| 30. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the front seat inner belt LH with the nut.
![]() |
Connect the connector and engage the 5 clamps.
| 31. INSTALL LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch) |
![]() |
Connect the connector.
Install the leg support adjustment switch with the 2 screws.
Engage the 2 wire harness clamps.
| 32. INSTALL FRONT POWER SEAT LUMBAR SWITCH |
![]() |
Install the front power seat lumbar switch with the 2 screws.
Connect the connector.
| 33. INSTALL FRONT SEAT CUSHION SHIELD LH |
![]() |
Connect the switch connectors.
Attach the 2 claws to install the cushion shield.
Install the 3 screws.
![]() |
Install the 2 screws.
Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.
| 34. INSTALL RECLINING POWER SEAT SWITCH KNOB |
![]() |
Attach the 2 claws to install the knob.
| 35. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Attach the 2 claws to install the knob.
| 36. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side) |
Check that the ignition switch is turned off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.
![]() |
Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.
Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).
Connect the connector to the seat position airbag sensor.
Check that there is no looseness in the installation parts of the seat position airbag sensor.
Engage the pin and install a new seat position sensor protector.
| 37. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Check that the ignition switch is off.
Check that the negative battery (-) terminal is disconnected.
Engage the claw and occupant classification ECU.
Connect the 2 connectors to the occupant classification ECU.