Home › Vehicle Interior › SEAT › REAR SEATBACK HEATER

REAR SEATBACK HEATER > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. INSTALL SEATBACK HEATER ASSEMBLY


    B191093
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new 8 tack pins.

    HINT:
    Do not bend or fold the seatback heater assembly.



2. INSTALL SEPARATE TYPE REAR SEATBACK COVER


    B191107E03
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



3. INSTALL SEATBACK COVER WITH PAD


    B191104
  1. Attach the hooks to install the seatback cover with pad.



    B191103E01
  1. Using hog ring pliers, install the seatback cover to the seatback frame with 2 new hog rings.



    B200254
  1. Connect the connector and Attach the wire harness clamp.



4. INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY RH


    B200244E03
  1. Attach the hooks.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

  1. Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the seatback frame with 2 new hog rings.



5. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    B191134E02
  1. Align the protruding portion of the rear seat headrest supports with the installation grooves of the rear seatback frame.
    Text in Illustration 
    *a
    Protruding

  1. Attach the 4 claws to install the 2 supports.



6. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191100E01
  1. Connect the cable in the order shown in the illustration to install the lock control lever sub-assembly.

  1. Install the rear seat lock control lever sub-assembly with the 2 screws.



7. INSTALL REAR SEATBACK LOCK STRIKER COVER


    B191099
  1. Attach the guide and claw to install the rear seatback lock striker cover.



8. INSTALL REAR SEAT CUSHION UNDER COVER RH


    B191097
  1. Install the rear seat cushion under cover with the 3 screws.



9. INSTALL REAR SEAT CUSHION HINGE COVER RH


    B191096
  1. Attach the 3 claws to install the rear seat cushion hinge cover.

  1. Install the 2 screws.



10. INSTALL REAR SEAT CUSHION HINGE COVER NO. 1


    B191095
  1. Attach the 4 claws and clip to install the rear seat cushion hinge cover.

  1. Install the screw.



11. INSTALL REAR SEAT BACK BOARD SUB-ASSEMBLY RH


    B191101
  1. Attach the 7 clips to install the rear seatback board sub-assembly.



12. INSTALL REAR SEAT HEADREST ASSEMBLY


13. INSTALL NO. 1 SEAT CUSHION COVER RH


    B191122
  1. Attach the claw to install the No. 1 seat cushion cover.

  1. Install the 2 screws.

  1. Attach the cable clamp and connect the cable to the No. 1 seat cushion cover.



    B200249
  1. When installing the No. 1 seat cushion cover, pass the cable under the cover, as shown in the illustration.



14. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B191091E01
  1. Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket, install the 2 "TORX" bolts.

    1. for Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



    B232099
  1. Fasten the cable to the seat cushion spring with 2 clamps and connect the cable.

    HINT:
    Align the cable with the alignment marks on the seat cushion spring.



    B191089
  1. Fasten the cable with a cable tie.

  1. Attach the cable clamp and connect the cable to the seat cushion spring.



    B191088
  1. Fasten the cable to the seat cushion spring with a cable tie and connect the cable.



    B191090
  1. Connect the connector and attach the 3 harness clamps.

    HINT:
    If the vehicle is equipped with the seat heater system, connect the connector and attach the clamps.



15. INSTALL REAR SEAT CUSHION HINGE COVER NO. 2


B191085
  1. Attach the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



16. INSTALL REAR SEAT CUSHION HINGE COVER NO. 3


B191084
  1. Attach the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



17. INSTALL REAR SEAT RECLINING RELEASE LEVER


    B191083
  1. Install the rear seat reclining release lever with the 3 screws.



18. INSTALL RECLINING ADJUSTER KNOB CAP RH


    B191082
  1. Attach the 3 claws to install the reclining adjuster knob cap.



    B200250E02
  1. Press the pink button on the rear seatback lock control No. 1 cable to release the cable lock, operate the lever a few times to adjust the amount of cable play, and then push in the pink button to lock the cable.
    Text in Illustration 
    *a
    Pink Button



19. INSTALL REAR NO. 1 SEAT ASSEMBLY RH
  1. Install the rear No. 1 seat assembly (Click here).